LT6012 Linear Technology, LT6012 Datasheet - Page 6

• Manufacturer Part Number: LT6012
• Description: (LT6011 / LT6012) Rail-to-Rail Output Precision Op Amp
• Manufacturer: Linear Technology

ELECTRICAL CHARACTERISTICS
LT6011/LT6012
temperature range, otherwise specifications are at T
SYMBOL
I
SR
GBW
t
t
I
Note 1: Absolute Maximum Ratings are those beyond which the life if the
device may be impaired.
Note 2: The inputs are protected by back-to-back diodes and internal
series resistors. If the differential input voltage exceeds 10V, the input
current must be limited to less than 10mA.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum ratings.
Note 4: Both the LT6011C/LT6012C and LT6011I/LT6012I are guaranteed
functional over the operating temperature range of – 40 C to 85 C.
Note 5: The LT6011C/LT6012C are guaranteed to meet the specified
performance from 0 C to 70 C and is designed, characterized and
expected to meet specified performance from – 40 C to 85 C but is not
tested or QA sampled at these temperatures. The LT6011I/LT6012I are
guaranteed to meet specified performance from –40 C to 85 C.
6
SC
s
r
S
, t
V
I
CMRR
PSRR
B
OS
f
PARAMETER
Output Short-Circuit Current
(Note 3)
Slew Rate
Gain Bandwidth Product
Settling Time
Rise Time, Fall Time
Offset Voltage Match (Note 7)
Input Bias Current Match (Note 7)
Common Mode Rejection Ratio
Match (Note 7)
Power Supply Rejection Ratio
Match (Note 7)
Supply Current
CONDITIONS
V
V
A
T
T
f = 10kHz
A
A
LT6011AS8, LT6012AS
T
T
LT6011ADD, LT6012AGN
T
T
LT6011S8, LT6012S
T
T
LT6011DD, LT6012GN
T
T
LT6011AS8, LT6011ADD, LT6012AS, LT6012AGN
T
T
LT6011S8, LT6011DD, LT6012S, LT6012GN
T
T
per Amplifier
T
T
OUT
OUT
V
A
A
V
V
A
A
A
A
A
A
A
A
A
A
A
A
A
A
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= 0 C to 70 C
= –40 C to 85 C
= –10, R
= –1, 0.01%, V
= 1, 10% to 90%, 0.1V Step
A
= 25 C. V
= 0V, 1V Overdrive (Source)
= 0V, –1V Overdrive (Sink)
The
F
= 50k, R
S
denotes the specifications which apply over the full operating
OUT
= 15V, V
G
= 0V to 10V
Note 6: This parameter is not 100% tested.
Note 7: Matching parameters are the difference between any two
amplifiers. CMRR and PSRR are defined as follows: (1) CMRR and
PSRR are measured in V/V for the individual amplifiers. (2) The
difference between matching amplifiers is calculated in V/V. (3) The
result is converted to dB.
Note 8: The specifications for V
the package. The following table clarifies the notations.
S8 Package
DFN Package
S14 Package
GN16 Package
= 5k
CM
= 0V, R
L
to 0V, unless otherwise specified. (Note 5)
STANDARD GRADE
LT6011S8
LT6011DD
LT6012S
LT6012GN
OS
, I
0.08
0.07
0.05
MIN
275
250
109
106
B
10
10
5
5
, and I
OS
0.11
TYP
350
135
135
260
depend on the grade and on
15
20
85
50
50
70
80
50
1
A GRADE
LT6011AS8
LT6011ADD
LT6012AS
LT6012AGN
1200
1800
2400
3000
MAX
270
320
370
320
420
450
300
350
400
400
500
550
600
900
330
380
400
sn60112 60112fas
UNITS
V/ s
V/ s
V/ s
kHz
kHz
m A
mA
m A
mA
pA
pA
pA
pA
pA
pA
dB
dB
V
V
V
V
V
V
V
V
V
V
V
V
A
A
A
s
s