SAM3S ATMEL [ATMEL Corporation], SAM3S Datasheet - Page 17
SAM3S
Manufacturer Part Number
SAM3S
Description
ARM-based Flash MCU
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.SAM3S.pdf
(64 pages)
- Current page: 17 of 64
- Download datasheet (2Mb)
5. Power Considerations
5.1
5.2
5.3
6500CS–ATARM–24-Jan-11
Power Supplies
Voltage Regulator
Typical Powering Schematics
The SAM3S product has several types of power supply pins:
The SAM3S embeds a voltage regulator that is managed by the Supply Controller.
This internal regulator is intended to supply the internal core of SAM3S. It features two different
operating modes:
• In Backup mode, the voltage regulator consumes less than 1 µA while its output (VDDOUT) is
driven internally to GND. The default output voltage is 1.80V and the start-up time to reach Nor-
mal mode is inferior to 100 µs.
For adequate input and output power supply decoupling/bypassing, refer to the Voltage Regula-
tor section in the Electrical Characteristics section of the datasheet.
The SAM3S supports a 1.62V-3.6V single supply mode. The internal regulator input connected
to the source and its output feeds VDDCORE.
As VDDIN powers the voltage regulator, the ADC/DAC and the analog comparator, when the
user does not want to use the embedded voltage regulator, it can be disabled by software via
the SUPC (note that it is different from Backup mode).
• VDDCORE pins: Power the core, the embedded memories and the peripherals; voltage
• VDDIO pins: Power the Peripherals I/O lines (Input/Output Buffers); USB transceiver; Backup
• VDDIN pin: Voltage Regulator Input, ADC, DAC and Analog Comparator Power Supply;
• VDDPLL pin: Powers the PLLA, PLLB, the Fast RC and the 3 to 20 MHz oscillator; voltage
• In Normal mode, the voltage regulator consumes less than 700 µA static current and draws
ranges from 1.62V and 1.95V.
part, 32kHz crystal oscillator and oscillator pads; ranges from 1.62V and 3.6V
Voltage ranges from 1.8V to 3.6V
ranges from 1.62V and 1.95V.
80 mA of output current. Internal adaptive biasing adjusts the regulator quiescent current
depending on the required load current. In Wait Mode quiescent current is only 7 µA.
Figure 5-1
shows the power schematics.
SAM3S Summary
17
Related parts for SAM3S
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64K Bytes In-System Programmable Programmable
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: