LTC2288 LINER [Linear Technology], LTC2288 Datasheet - Page 20

• Manufacturer Part Number: LTC2288
• Description: Dual 10-Bit, 65/40/25Msps Low Noise 3V ADCs
• Manufacturer: LINER [Linear Technology]

LTC2288/LTC2287/LTC2286
APPLICATIO S I FOR ATIO
The noise performance of the LTC2288/LTC2287/LTC2286
can depend on the clock signal quality as much as on the
analog input. Any noise present on the clock signal will
result in additional aperture jitter that will be RMS summed
with the inherent ADC aperture jitter.
In applications where jitter is critical, such as when digitiz-
ing high input frequencies, use as large an amplitude as
possible. Also, if the ADC is clocked with a sinusoidal
signal, filter the CLK signal to reduce wideband noise and
distortion products generated by the source.
It is recommended that CLKA and CLKB are shorted
together and driven by the same clock source. If a small
time delay is desired between when the two channels
sample the analog inputs, CLKA and CLKB can be driven
by two different signals. If this delay exceeds 1ns, the
performance of the part may degrade. CLKA and CLKB
should not be driven by asynchronous signals.
Maximum and Minimum Conversion Rates
The maximum conversion rate for the LTC2288/LTC2287/
LTC2286 is 65Msps (LTC2288), 40Msps (LTC2287), and
25Msps (LTC2286). For the ADC to operate properly, the
CLK signal should have a 50% (±5%) duty cycle. Each half
cycle must have at least 7.3ns (LTC2288), 11.8ns
(LTC2287), and 18.9ns (LTC2286) for the ADC internal
circuitry to have enough settling time for proper operation.
20
SINUSOIDAL
Figure 11. Sinusoidal Single-Ended CLK Drive
CLOCK
INPUT
50Ω
U
4.7µF
0.1µF
1k
U
1k
NC7SVU04
FERRITE
W
0.1µF
BEAD
CLK
SUPPLY
CLEAN
LTC2288
LTC2287
LTC2286
228876 F11
U
An optional clock duty cycle stabilizer circuit can be used
if the input clock has a non 50% duty cycle. This circuit
uses the rising edge of the CLK pin to sample the analog
input. The falling edge of CLK is ignored and the internal
falling edge is generated by a phase-locked loop. The
input clock duty cycle can vary from 40% to 60% and the
clock duty cycle stabilizer will maintain a constant 50%
internal duty cycle. If the clock is turned off for a long
period of time, the duty cycle stabilizer circuit will require
a hundred clock cycles for the PLL to lock onto the input
clock. To use the clock duty cycle stabilizer, the MODE pin
should be connected to 1/3V
resistors. The MODE pin controls both Channel A and
Channel B—the duty cycle stabilizer is either on or off for
both channels.
The lower limit of the LTC2288/LTC2287/LTC2286 sample
rate is determined by droop of the sample-and-hold cir-
cuits. The pipelined architecture of this ADC relies on
storing analog signals on small valued capacitors. Junc-
tion leakage will discharge the capacitors. The specified
minimum operating frequency for the LTC2288/LTC2287/
LTC2286 is 1Msps.
DIGITAL OUTPUTS
Digital Output Buffers
Figure 12 shows an equivalent circuit for a single output
buffer. Each buffer is powered by OV
lated from the ADC power and ground. The additional
N-channel transistor in the output driver allows operation
down to low voltages. The internal resistor in series with
the output makes the output appear as 50Ω to external
circuitry and may eliminate the need for external damping
resistors.
As with all high speed/high resolution converters, the digi-
tal output loading can affect the performance. The digital
outputs of the LTC2288/LTC2287/LTC2286 should drive a
minimal capacitive load to avoid possible interaction
DD
or 2/3V
DD
DD
and OGND, iso-
using external
228876f