LT1461 LINER [Linear Technology], LT1461 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
LT1461
Manufacturer Part Number
LT1461
Description
Easy-to-Use, Ultra-Tiny, Differential, 16-Bit ADC With I2C Interface
Manufacturer
LINER [Linear Technology]
Datasheet
1.LT1461.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1461ACS8-10
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LT1461ACS8-2.5
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT1461ACS8-2.5
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1461ACS8-2.5#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1461ACS8-2.5#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT1461ACS8-3
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LT1461ACS8-3.3
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT1461ACS8-4
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT1461ACS8-5
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT1461ACS8-5#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS INFORMATION
Data Transferring
After the START condition, the I
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit. The
master releases the SDA line during the ninth SCL clock
cycle. The slave device can issue an ACK by pulling SDA
LOW or issue a Not Acknowledge (NAK) by leaving the
SDA line HIGH impedance (the external pull-up resistor
will hold the line HIGH). Change of data only occurs while
the clock line (SCL) is LOW.
Data Format
After a START condition, the master sends a 7-bit address
followed by a read request (R) bit. The bit R is 1 for a Read
Request. If the 7-bit address matches the LTC2453’s ad-
dress (hard-wired at 0010100) the ADC is selected. When
the device is addressed during the conversion state, it does
not accept the request and issues a NAK by leaving the
SDA line HIGH. If the conversion is complete, the LTC2453
issues an ACK by pulling the SDA line LOW.
SDA
SCL
SCL
SDA
t
f
S
START BY
MASTER
t
HD(STA)
t
LOW
Figure 3. Defi nition of Timing for Fast/Standard Mode Devices on the I
SLEEP
ADDRESS
1
7-BIT
2
t
r
C bus is busy and data
t
HD(DAT)
7
t
8
SU(DAT)
R
Figure 4. Read Sequence Timing Diagram
LTC2453
ACK BY
t
HIGH
9
1
D15
SGN
t
f
MSB
2
D14
t
SU(STA)
3
D13
Following the ACK, the LTC2453 can output data. The data
output stream is 16 bits long and is shifted out on the
falling edges of SCL (see Figure 4). The fi rst bit output by
the LTC2453 is the sign, which is 1 for V
for V
lowed by successively less signifi cant bits (D13, D12…)
until the LSB is output by the LTC2453. This sequence is
shown in Figure 5.
OPERATION SEQUENCE
Continuous Read
Conversions from the LTC2453 can be continuously
read, see Figure 6. At the end of a read operation, a new
conversion automatically begins. At the conclusion of
the conversion cycle, the next result may be read using
the method described above. If the conversion cycle is
not complete and a valid address selects the device, the
LTC2453 generates a NAK signal indicating the conversion
cycle is in progress.
Sr
DATA OUTPUT
IN
D8
8
+
< V
t
MASTER
HD(SDA)
ACK BY
9
IN
–
. The next bit is the MSB (D14) and is fol-
1
D7
2
D6
t
SP
t
SU(STO)
3
D5
2
C Bus
t
r
LSB
D0
P
8
NACK BY
MASTER
t
BUF
9
CONVERSION
LTC2453
2453 F04
IN
S
2453 F03
+
≥ V
IN
–
and 0
9
2453f