NIPCI-4351 NI [National Instruments Corporation], NIPCI-4351 Datasheet - Page 5

• Manufacturer Part Number: NIPCI-4351
• Description: High-Precision Data Acquisition
• Manufacturer: NI [National Instruments Corporation]

High-Precision Data Acquisition
Open-thermocouple detection .............. 10 MΩ between CH+ and +2.5 V
Ground-referencing ............................... 10 MΩ between CH- and ground
Input bias current .................................. <500 pA
CMR (DC, 50 Hz, 60 Hz, 400 Hz)
NMR (50 Hz, 60 Hz, 400 Hz) .................. >100 dB
Dynamic Characteristics
Bandwidth ............................................. 20 Hz
Excitation
Digital I/O and Alarm Outputs
Number of lines .................................... 8
Compatibility ......................................... TTL
Digital Logic Levels
Power-on state ...................................... Tristate (weak pull-up)
Data transfers ....................................... Programmed I/O
Bus interface ......................................... PCI, PXI, USB
Power Requirements
+5 VDC
Physical
Dimensions
I/O connector......................................... 68-pin male, shielded and latched
Environment
Operating temperature.......................... 0 to 55 °C
Storage temperature ............................. -20 to 70 °C
Relative humidity .................................. 10 to 90%, noncondensing
Parameter
Range ≥2.5 V .................................... 80 dB
Range <2.5 V..................................... 100 dB
PCI-4351............................................ 480 mA
PXI-4351............................................ 480 mA
PCI ..................................................... 11.2 by 18.8 cm (4.4 by 7.4 in.)
PXI ..................................................... 10.0 by 16.0 cm (3.9 by 6.3 in.), 3U
±Ex0
±Ex1
Level
25 µA
1 mA
Maximum Load Resistance
600 kΩ
15 kΩ
(software selectable)
(software selectable)
Temperature Coefficient
±15 ppm
±15 ppm
Safety and Compliance
Safety
This product is designed to meet the requirements of the following standards of
safety for electrical equipment for measurement, control, and laboratory use:
◾ ◾
◾ ◾
Note: For UL and other safety certifications, refer to the product label or visit
ni.com/certification
appropriate link in the Certification column.
Electromagnetic Compatibility
This product is designed to meet the requirements of the following standards of
EMC for electrical equipment for measurement, control, and laboratory use:
◾ ◾
◾ ◾
◾ ◾
Note: For EMC compliance, operate this device according to
product documentation.
CE Compliance
This product meets the essential requirements of applicable European Directives,
as amended for CE marking, as follows:
◾ ◾
◾ ◾
Note: Refer to the Declaration of Conformity (DoC) for this product for any
additional regulatory compliance information. To obtain the DoC for this product,
visit
the appropriate link in the Certification column.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers: At the end of their life cycle, all products must be
sent to a WEEE recycling center. For more information about WEEE
recycling centers and National Instruments WEEE initiatives,
visit
IEC 61010-1, EN 61010-1
UL 61010-1, CSA 61010-1
EN 61326 EMC requirements; Minimum Immunity
EN 55011 Emissions; Group 1, Class A
CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A
2006/95/EC; Low-Voltage Directive (safety)
2004/108/EC; Electromagnetic Compatibility Directive (EMC)
ni.com/certification
ni.com/environment/weee.htm
, search by model number or product line, and click the
BUY ONLINE at ni.com or C
, search by model number or product line, and click
.
ALL 800 813 36
93 (U.S.)
5