DG441/883 INTERSIL [Intersil Corporation], DG441/883 Datasheet
DG441/883
Related parts for DG441/883
DG441/883 Summary of contents
Page 1
... The four switches are bilateral, equally matched for AC or bidirectional signals. The ON resistance variation with analog signals is quite low over a ±5V analog input range. The switches in the DG441/883 and DG442/883 are identical, dif- fering only in the polarity of the selection logic. Ordering Information ...
Page 2
... No Internal Connection 13 V+ Positive Power Supply Terminal (Substrate Source (Input) Terminal for Switch Drain (Output) Terminal for Switch Logic Control for Switch 2 2 DG441/883, DG442/883 LOGIC ≤0.8V 0 ≥2. TRUTH TABLE V DG441 DG442 IN ON OFF OFF ON ...
Page 3
... Specifications DG441/883, DG442/883 Absolute Maximum Ratings 44V GND 25V Digital Inputs, (Note (V-) - 30mA, Continuous Current (Note 1 ±30mA Peak Current (Note .±100mA Storage Temperature Range (A Suffix -65 Lead Temperature (Soldering 10s +300 CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied ...
Page 4
... Specifications DG441/883, DG442/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued ≤ T ≤ +125 o Device Tested at: - +15V -15V, Unless Otherwise Specified A PARAMETERS SYMBOL Drain OFF Leakage Current I D(OFF) DG441/883 DG442/883 Channel ON Leakage Current I + D(ON) I S(ON) DG441/883 DG442/883 Input Current with V Low ...
Page 5
... Specifications DG441/883, DG442/883 TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS o C ≤ T ≤ +125 o Device Tested at: - +15V -15V, Unless Otherwise Specified A PARAMETERS SYMBOL Turn ON Time t ON DG441 DG442 DG441 DG442 DG441 DG442 DG441 DG442 Turn OFF Time t OFF DG441 DG442 DG441 ...
Page 6
... Type: Nitride ± 1k Å Å Thickness: 8k WORST CASE CURRENT DENSITY 1 A/cm Metallization Mask Layout D 1 ( (4) GND (5) S (6) 4 (7) D DG441/883, DG442/883 DG441/883, DG442/883 (1) (16) (8) ( (15 (14 (13) V+ SUBSTRATE (12) NC (11 (10) D ...
Page 7
... < 20ns (90 SWITCH S 1 INPUT IN 1 LOGIC INPUT 3V 0 Repeat test for Channels 2, 3 and 4. For load conditions, see Specifications C stray capacitance) FIGURE 1. SWITCHING TIME DG441/883, DG442/883 OUT OUT ...
Page 8
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com DG441/883, DG442/883 66 S ...
Page 9
... Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. DG441/883, DG442/883 F16.3 c1 LEAD FINISH MIL-STD-1835 GDIP1-T16 (D-2, CONFIGURATION A) 16 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE ...
Page 10
TM DESIGN INFORMATION June 1994 The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves AND ...
Page 11
DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves CROSSTALK AND OFF ISOLATION vs FREQUENCY 140 ...
Page 12
DESIGN INFORMATION The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves SOURCE/DRAIN CAPACITANCE vs ANALOG VOLTAGE (SINGLE 12V ...