AS1100PE-Z AMSCO [austriamicrosystems AG], AS1100PE-Z Datasheet - Page 8

• Manufacturer Part Number: AS1100PE-Z
• Description: Serially Interfaced, 8-Digit LED Driver
• Manufacturer: AMSCO [austriamicrosystems AG]

Data Sheet AS1100
Display Test Register
With the display test register 0Fh all LED can be tested. In
the test mode all LEDs are switched on at maximum
brightness (duty cycle 31/32). All programming of digit and
control registers is maintained. The format of the register is
given in table 10.
Table 9: Maximum segment current for 1-, 2-, or 3-digit displays
Table 10: Display-test register format (address (hex) = 0xXF)
Note: The AS1100 remains in display-test mode until the
display-test register is reconfigured for normal operation.
No-Op Register (Cascading of As1100)
The no-operation register 00h is used when AS1100s are
cascaded in order to support more than 8 digit displays. The
cascading must be done in a way that all DOUT are
connected to DIN of the following AS1100. The LOAD and
CLK signals are connected to all devices. For a write
operation for example to the fifth device the command must
be followed by four no-operation commands. When the
LOAD signal finally goes to high all shift registers are
latched. The first four devices have got no-operation
commands and only the fifth device sees the intended
command and updates its register.
Reset and external Clock Register
This register is addressed via the serial interface. It allows
to switch the device to external clock mode (If D0=1 the
CLK pin of the serial interface operates as system clock
input.) and to apply an external reset (D1). This brings all
registers (except reg. E) to default state. For standard
operation the register contents should be "00h".
3
software reset and external clocks
Revision 1.32, Oct. 2004
Mode
Normal Operation X
Display Test
Mode
This register is not used by MAX7219, since it does not support
Number of
Digits
Displayed
1
2
3
D7 D6 D5 D4 D3 D2 D1 D0
X
Maximum
Segment Current
(mA)
10
20
30
X
X
X
X
Register Data
X
X
3
X
X
X
X
X
X
0
1
Table 11: Reset and external Clock register (address (hex) = 0xXE)
Applications Information
Supply Bypassing and Wiring
In order to achieve optimal performance the AS1100 shall
be placed very close to the LED display to minimize effects
of electromagnetic interference and wiring inductance.
Furthermore it is recommended to connect a 10µF
electrolytic and a 0.1µF ceramic capacitor between VDD
and GND to avoid power supply ripple. Also, both GNDs
must be connected to ground.
Selecting R
The current through the segments is controlled via the
external resistor R
the current in I
table 12. The maximum current the AS1100 can drive is
40mA. If higher currents are needed, external drivers must
be used. In that case it is no longer necessary that the
AS1100 drives high currents. A recommended value for
R
digits table 9 specifies the maximum currents and R
be set accordingly. Refer to absolute maximum ratings to
calculate
segment current, and the LED forward-voltage drop.
Table 12: RSET vs. segment current and LED forward voltage
Mode
Normal Operation,
internal clock
Normal Operation,
external clock
Reset state,
internal clock
Reset state,
external clock
SET
I
SEG
is 47k . In cases that the AS1100 only drives few
40
30
20
10
(mA)
acceptable
SET
Resistor and Using External Drivers
SET
12.2
17.8
29.8
66.7
1.5
SET
. The right values for I
code (hex)
. Segment current is about 100 times
Address
0xXE
0xXE
0xXE
0xXE
11.8
17.1
28.0
63.7
limits
2.0
V
LED
11.0
15.8
25.9
59.3
for
2.5
D7 D6 D5 D4 D3 D2 D1 D0
X X X X X X
X X X X X X
X X X X X X
X X X X X X
(V)
ambient
10.6
15.0
24.5
55.4
3.0
Register Data
SET
9.69
14.0
22.6
51.2
3.5
are given in
temperature,
Page 8 of 12
SET
must
0
0
1
1
0
1
0
1