MIC5210-MPYMM MICREL [Micrel Semiconductor], MIC5210-MPYMM Datasheet
MIC5210-MPYMM
Related parts for MIC5210-MPYMM
MIC5210-MPYMM Summary of contents
Page 1
... Designed especially for hand-held battery powered devices, the MIC5210 can be switched by a CMOS or TTL compatible logic signal, or the enable pin can be connected to the supply input for 3-terminal operation. When disabled, power consumption drops nearly to zero. ...
Page 2
... MIC5210-3.0BMM MIC5210-3.3BMM MIC5210-3.6BMM MIC5210-4.0BMM MIC5210-5.0BMM MIC5210-2.8/3.0BMM MP * Other voltages available. Contact Micrel for details. ** Order Entry P/N for Pb-Free has been abbreviated in compliance with Micrel systems. MIC5210-MPYMM = Full P/N: MIC5210-2.8/3.0YMM. Voltage Code Key 2.8 M 3.0 P September 2006 Pb-Free ...
Page 3
... May be left open. Enable/Shutdown B (Input): CMOS compatible input. Logic high = enable, logic low or open = shutdown. Do not leave floating. Supply Input B Enable/Shutdown A (Input): CMOS compatible input. Logic high = enable, logic low or open = shutdown. Do not leave floating. Supply Input A 3 MIC5210 M9999-090806 ...
Page 4
... 100mA 150mA L Frequency = 100Hz 100µ OUT Note 50mA 2.2µ 470pF from BYPB to GND 4 MIC5210 )................................. 2.5V to 16V IN )................................... 0V to 16V EN ) .......................... –40°C to +85°C J ).......................................... Note 1 JA < +125°C, unless noted. J Min Typ Max Units – –2 2 ppm/° ...
Page 5
... The maximum allowable power dissipation at any ambient temperature θ . Exceeding the maximum allowable power dissipation will result in excessive die temperature, and the the 8-pin MSOP (MM) is 200°C/W mounted board (see “Thermal Considerations” section JA = 16V for t = 10ms MIC5210 Min Typ Max Units 0 0.18 V 2.0 0.01 – ...
Page 6
... -20 OUT -40 - 100mA OUT - 2.2µF OUT C = 0.01µF BYP -100 1E+1 1E+21E+3 1E+41E+5 1E+61E+7 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 6 MIC5210 Power Supply Rejection Ratio -20 OUT -40 -60 - 10mA OUT C = 1µF OUT -100 1E+1 1E+21E+3 1E+41E+5 1E+61E+7 ...
Page 7
... OUT C = 10µF 10mA OUT 0.001 electrolytic C = 10nF BYP 0.0001 10 1E+11E+2 1E+31E+4 1E+51E+61E+7 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 7 MIC5210 Noise Performance (Regulator 100mA 0.1 0.01 1mA OUT C = 10µF OUT 0.001 electrolytic 10mA C = 100pF BYP 0.0001 1E+11E+2 1E+31E+4 1E+51E+61E+7 ...
Page 8
... Micrel, Inc. Block Diagram September 2006 8 MIC5210 M9999-090806 ...
Page 9
... September 2006 No-Load Stability The MIC5210 will remain stable and in regulation with no load (other than the internal voltage divider) unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. ...
Page 10
... This means, using the same 5V input and 3.3V output voltage, the second regulator is limited to about 60mA. September 2006 Taking advantage of the extremely low-dropout voltage characteristics of the MIC5210, power dissipation can be reduced by using the lowest possible input voltage to minimize the input-to-output voltage drop. 10 ...
Page 11
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully September 2006 8-Pin MSOP (MM) indemnify Micrel for any damages resulting from such use or sale. © 2003 Micrel, Incorporated. 11 MIC5210 M9999-090806 ...