ex256-ptqg100i Actel Corporation, ex256-ptqg100i Datasheet - Page 9

no-image

ex256-ptqg100i

Manufacturer Part Number
ex256-ptqg100i
Description
Fpga Ex Family 4k Gates 256 Cells 250mhz 0.22um Cmos Technology 2.5v 100-pin Tqfp
Manufacturer
Actel Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EX256-PTQG100I
Manufacturer:
Microsemi SoC
Quantity:
10 000
Other Architectural Features
Performance
The combination of the various architectural features
enables automotive-grade eX devices to operate with
internal clock frequencies at 250 MHz for fast execution
of complex logic functions.
Automotive-grade eX devices are the optimal platforms
upon which to integrate in-cabin telematics and
automobile interconnect applications previously only
contained in ASICs or gate arrays.
eX devices meet the performance goals of gate arrays,
and, at the same time, present significant improvements
in cost and time to market. Using timing-driven place-
and-route
deterministic device performance.
User Security
The Actel FuseLock advantage ensures that unauthorized
users will not be able to read back the contents of an
Actel antifuse FPGA. In addition to the inherent
strengths of the architecture, there is a special Security
Fuse inside the eX device that disables the probing
circuitry and prohibits further programming of the
device. This Fuse cannot be accessed or bypassed without
destroying access to the rest of the device, making both
invasive and more-subtle noninvasive attacks ineffective
against Actel antifuse FPGAs.
Look for this symbol to ensure your valuable IP is secure.
Figure 1-7 • FuseLock
For more information, refer to Actel's
Security in Actel Antifuse FPGAs
I/O Modules
Each I/O on an eX device can be configured as an input, an
output, a tristate output, or a bidirectional pin. I/O cells in
eX devices do not contain embedded latches or flip-flops
and can be inferred directly from HDL code. The device
can easily interface with any other device in the system,
which in turn enables parallel design of system
components and reduces overall design time.
All unused I/Os are configured as tristate outputs by
Actel's Designer software, for maximum flexibility when
designing new boards or migrating existing designs.
However, it is still recommended to tie all unused I/O pins
tools,
designers
FuseLock
application note.
can
Implementation of
achieve
highly
v3.2
to GND on the board. Each I/O module has an available
pull-up or pull-down resistor of approximately 50 kΩ
that can configure the I/O in a known state during
power-up. Just shortly before V
resistors are disabled and the I/Os will be controlled by
user logic.
Table 1-2
more information on I/Os, refer to the
and RT54SX-S I/Os
The automotive eX devices support I/O operation at 2.5 V
and 3.3 V.
The detailed description of the I/O pins in eX automotive
devices can be found in
page
Table 1-2 • I/O Features
Hot Swapping
eX I/Os are configured to be hot-swappable. During
power-up/down (or partial up/down), all I/Os are tristated,
provided V
and V
and they do not require a specific power-up or power-
down sequence in order to avoid damage to the eX
devices. In addition, all outputs can be programmed to
have a weak resistor pull-up or pull-down for tristate
output at power-up. After the eX device is plugged into
an electrically active system, the device will not degrade
the reliability of or cause damage to the host system. The
device's output pins are driven to a high impedance state
until normal chip operating conditions are reached. Please
see the application note,
in Hot-Swap and Cold-Sparing
applies to eX devices, for more information on hot
swapping.
Function
Input
Threshold
Selection
Nominal
Output Drive
Output Buffer “Hot-Swap” Capability
Power-Up
1-24.
CCI
Buffer
do not have to be stable during power-up/down,
describes the I/O features of eX devices. For
CCA
Description
Individually selectable low-slew option
Individually selectable pull-ups and pull-downs
during power-up (default is to power-up in
tristate)
Enables deterministic power-up of device
V
ramps up within a diode drop of V
CCA
Selectable on an individual I/O basis
3.3 V LVTTL
2.5 V LVCMOS2
3.3 V LVTTL
2.5 V LVCMO 2
I/O on an unpowered device does not sink
current
Can be used for “cold sparing”
application note.
and V
CCI
Actel SX-A and RT54SX-S Devices
"Pin Description" section on
eX Automotive Family FPGAs
can be powered in any order
Applications, which also
CCA
reaches 2.5 V, the
Actel eX, SX-A,
CCI
. V
CCA
1-5

Related parts for ex256-ptqg100i