pt8a2621w Pericom Technology Inc, pt8a2621w Datasheet
pt8a2621w
Available stocks
Related parts for pt8a2621w
pt8a2621w Summary of contents
Page 1
... With on chip noise filter and voltage regulator, the IC provides stable operations throughout temperature range. CDS input to disable day time operation is desired. Function Comparison PT8A2611 PT8A2621 Ordering Information PT8A2611P / PT8A2621P PT8A2611W / PT8A2621W PT8A2611DE / PT8A2621DE Comparator latch circuit (Internal CDS feedback, Voltage for 2611 only) divider ...
Page 2
Pad Location Pad Location of PT8A2611DE Die No. Pad Name X Coordinate GND 570 TRIAC 570 OSCD 570 OSCS 570 ZC -378.8 CDS -30.1 MODE 570 V -197 136.9 CC Note: Substrate is connected to GND PT0091(11/03) ...
Page 3
Pad Location of PT8A2621DE Die No. Pad Name X Coordinate GND 570 RELAY 570 OSCD 570 OSCS 570 ZC -378.8 CDS -30.1 MODE 570 V -197 136.9 CC Note: Substrate is connected to GND PT0091(11/03) PIR Sensor ...
Page 4
... Non-inverted input of first operational amplifier, connected directly to source of PIR sensor Inverted input of first operational amplifier Output of first operational amplifier Non-inverted input of second operational amplifier. Inverted input of second operational amplifier Output of second operational amplifier 4 PT8A2611/2621 PIR Sensor Light Switch Controller PT8A2621P/PT8A2621W GND 1 16 OP2O 2 15 OP2N 3 ...
Page 5
Functional Descriptions The PT8A2611 and PT8A2621 are CMOS LSI chips designed for automatic PIR lamp control. They can operate in 2-wire configuration for triac applications or in 3-wire configuration for relay applications. The PIR sensor detects infrared power variations ...
Page 6
MODE MODE is a tri-state input pin for operation mode selection. See the following table 2. Override Control (for PT8A2621 only): The term override re- fers to the change of operating mode by switching the power switch twice within ...
Page 7
Power On Initial The PIR signal amplifier requires a warm up period after power- on. The input should be disabled during this period. In the AUTO mode within the first 40 seconds of the initial time the chip allows ...
Page 8
Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested) Storage Temperature ............................................................-40 Supply V oltage to Ground Potential (Inputs & V Supply V oltage to Ground Potential (Outputs & D/O Only) -0.3 to ...
Page 9
AC Electrical Characteristics Voltage Regulator Sym Description V Output Voltage EE V Noninverting input of OP2 OP2P V Line Regulation V Load Regulation LDR I Regulator Output Current L Operational Amplifier and Window Comparator Sym Description BW 3dB Bandwidth ...
Page 10
Oscillator and ZC Input Pulse and Trigger Output Pulse Sym Description f Oscillator Frequency OSC t ZC Pulse Rise Time Pulse Fall Time Pulse Period Pulse Width ZW t TRIAC ...
Page 11
Typical Application Circuits Figure 9. Two-Wire Application Circuit of PT8A2611 PT0091(11/03) PIR Sensor Light Switch Controller 11 Data Sheet PT8A2611/2621 Ver:3 ...
Page 12
Figure 10. Three-Wire Application Circuit of PT8A2621 PT0091(11/03) PIR Sensor Light Switch Controller ON AUTO OFF 12 Data Sheet PT8A2611/2621 Ver:3 ...
Page 13
... Bering Drive, San Jose, California 95131, USA Tel: (1)-408-435 0800 Pericom Technology Incorporation reserves the right to make changes to its products or specifications at any time, without notice, in order to improve design or performance and to supply the best possible product. Pericom Technology does not assume any responsibility for use of any circuitry described other than the circuitry embodied in Pericom Technology product ...
Page 14
...