SI3215 SILABS [Silicon Laboratories], SI3215 Datasheet - Page 41
![no-image](/images/no-image-200.jpg)
SI3215
Manufacturer Part Number
SI3215
Description
Manufacturer
SILABS [Silicon Laboratories]
Datasheet
1.SI3215.pdf
(118 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3215-C-FM
Manufacturer:
SiliconL
Quantity:
230
Company:
Part Number:
SI3215-C-FMR
Manufacturer:
HOLTEK
Quantity:
26 000
Company:
Part Number:
SI3215-FM
Manufacturer:
SILICON
Quantity:
750
Part Number:
SI3215-FM
Manufacturer:
SILICONLABS/芯科
Quantity:
20 000
Company:
Part Number:
SI3215-FT
Manufacturer:
SILICON
Quantity:
15 000
Part Number:
SI3215-FT
Manufacturer:
SILICONIX
Quantity:
20 000
Part Number:
SI3215-KT
Manufacturer:
SILICONIX
Quantity:
20 000
Part Number:
SI3215M-C-FM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
SI3215M-C-FT
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
2.6.2. Receive Path
In the receive path, the optionally-compressed 8-bit
data is first expanded to 16-bit words. The PCMF
register bit can bypass the expansion process, in
which case two 8-bit words are assembled into one 16-
bit word. DACG is the receive path programmable gain
amplifier, which can be programmed from – ∞ dB to
6 dB. An 8 kHz, 16-bit signal is then provided to a D/A
converter. The resulting analog signal is amplified by
the analog receive amplifier, ARX, which is user-
selectable to one of mute/–3.5/0/3.5 dB options. It is
then applied at the input of the transconductance
amplifier (Gm), which drives the off-chip current buffer
(I
2.6.3. Audio Characteristics
The dominant source of distortion and noise in both the
transmit and receive paths is the quantization noise
introduced by the µ-law or the A-law compression
process. Figure 1 on page 7 specifies the minimum
signal-to-noise-and-distortion ratio for either path for a
sine wave input of 200 Hz to 3400 Hz.
Both the µ-law and the A-law speech encoding allow the
audio codec to transfer and process audio signals larger
than 0 dBm0 without clipping. The maximum PCM code
is generated for a µ-law encoded sine wave of
3.17 dBm0 or an A-law encoded sine wave of
3.14 dBm0. The ProSLIC overload clipping limits are
driven by the PCM encoding process. Figure 2 on page
7 shows the acceptable limits for the analog-to-analog
fundamental power transfer-function, which bounds the
behavior of ProSLIC.
The transmit path gain distortion versus frequency is
shown in Figure 3 on page 8. The same figure also
presents the minimum required attenuation for any out-
of-band analog signal that may be applied on the line.
Note the presence of a high-pass filter transfer-function,
which ensures at least 30 dB of attenuation for signals
below 65 Hz. The low-pass filter transfer function that
attenuates signals above 3.4 kHz has to exceed the
requirements specified by the equations in Figure 3 on
page 8, and it is implemented as part of the A-to-D
converter.
The receive path transfer function requirement, shown
in Figure 4 on page 9, is very similar to the transmit path
transfer function. The most notable difference is the
absence of the high-pass filter portion. The only other
differences are the maximum 2 dB attenuation at
200 Hz (as opposed to 3 dB for the transmit path) and
the 28 dB of attenuation for any frequency above
4.6 kHz. The PCM data rate is 8 kHz and, thus, no
frequencies greater than 4 kHz can be digitally encoded
in the data stream. From this point of view, at
BUF
).
Rev. 0.92
frequencies greater than 4 kHz, the plot in Figure 4
should be interpreted as the maximum allowable
magnitude of any spurious signals that are generated
when a PCM data stream representing a sine wave
signal in the range of 300 Hz to 3.4 kHz at a level of
0 dBm0 is applied at the digital input.
The group delay distortion in either path is limited to no
more than the levels indicated in Figure 5 on page 10.
The reference in Figure 5 on page 10 is the smallest
group delay for a sine wave in the range of 500 Hz to
2500 Hz at 0 dBm0.
The block diagram for the voice-band signal processing
paths are shown in Figure 22. Both the receive and the
transmit paths employ the optimal combination of
analog and digital signal processing to provide the
maximum performance while, at the same time, offering
sufficient flexibility to allow users to optimize for their
particular application of the ProSLIC. All programmable
signal-processing blocks are symbolically indicated in
Figure 22 by a dashed arrow across them. The two-wire
(TIP/RING) voice-band interface to the ProSLIC is
implemented using a small number of external
components. The receive path interface consists of a
unity-gain current buffer, I
interface is simply an ac coupling capacitor. Signal
paths, although implemented differentially, are shown
as single-ended for simplicity.
2.6.4. Transhybrid Balance
The ProSLIC provides programmable transhybrid
balance with gain block H. (See Figure 22.) In the ideal
case where the synthesized SLIC impedance matches
exactly the subscriber loop impedance, the transhybrid
balance should be set to subtract a –6 dB level from the
transmit path signal. The transhybrid balance gain can
be adjusted from –2.77 dB to +4.08 dB around the ideal
setting of –6 dB by programming the HYBA[2:0] bits of
the Hybrid Control register (direct Register 11). Note
that adjusting any of the analog or digital gain blocks will
not require any modification of the transhybrid balance
gain block, as the transhybrid gain is subtracted from
the transmit path signal prior to any gain adjustment
stages. The transhybrid balance can also be disabled, if
desired, using the appropriate register setting.
2.6.5. Loopback Testing
Four loopback test options are available in the ProSLIC:
The full analog loopback (ALM2) tests almost all the
circuitry of both the transmit and receive paths. The
compressed 8-bit word transmit data stream is fed
back serially to the input of the receive path
expander. (See Figure 22.) The signal path starts
with the analog signal at the input of the transmit
path and ends with an analog signal at the output of
BUF
, while the transmit path
Si3215
41