ATS45CS3 ETC2 [List of Unclassifed Manufacturers], ATS45CS3 Datasheet - Page 2

• Manufacturer Part Number: ATS45CS3
• Description: LOW-VOLTAGE ULTRA-LOW-POWER TEMPERATURE SENSOR WITH HIGH OUTPUT DRIVE
• Manufacturer: ETC2 [List of Unclassifed Manufacturers]

© Andigilog, Inc. 2006
Absolute Maximum Ratings
Recommended Operating Ratings
Electrical Characteristics
Limits apply for - 20°C ≤ T
Notes:
5.
6.
7.
8.
Supply Voltage
Output Voltage
Continuous Current, any terminal
Storage Temperature Range
ESD
Thermal Re-
sistance - θ
Lead Temp
Accuracy
Non-linearity
Supply Current - Output floating
Output Sink Capability
Output Source Capability
Average Output Slope (Sensor Gain)
Room Temp Output Voltage
Minimum Temperature
Self Heating
Symbol
V
Accuracy (expressed in °C) = Difference between calculated output voltage and measured output voltage.
Calculated output voltage = 10mV/°C multiplied by device’s case temperature at specified conditions of
temperature, voltage and power supply.
Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight
line, over the device’s rated temperature range.
Lowest output current should be targeted; higher currents result in more self-heating of the device.
Max Self Heating = θ
V
T
OUT
DD
2,3
A
5
JA
Supply Voltage
Output Voltage
Operating Temperature Range
8
6
Parameter
Parameter
Human Body Model
Machine Model
SOT-23
Soldering (10 sec)
Infrared (20 sec)
A
≤ +100°C and V
7
JA
Parameter
7
x (V
DD
4
x I
1
DD
D D
). Assumes a capacitive load.
= + 3.0V unless otherwise noted. Negative bias required for temperatures below 10 °C
Symbol
V
-60 ° C to +150 ° C
A
OUT25
I
I
I
OUT
DD
OL
OH
V
Class 1B
336°C/W
Class A
DD
Rating
260°C
235°C
www.andigilog.com
10mA
+7V
+ 0.5V
+2.7V < V
+2.7V < V
+2.7
- 20°C ≤ T
Min
-20
T
- 2 -
0
T
A
Single Supply
A
=+100°C (T
Conditions
=-20°C (T
T
T
T
See Fig 1
SOT-23
A
A
A
=+25°C
=+25°C
=+25°C
A
DD
DD
Notes:
≤ +100°C
+100
< +5.5V
< +5.5V
Max
+5.5
V
DD
MIN
MAX
1.
2.
3.
4.
)
)
Absolute maximum ratings are limits
beyond which operation may cause
permanent damage to the device. These
are stress ratings only; functional
operations at or above these limits is not
implied.
Human Body Model: 100pF capacitor
discharged through a 1.5k Ω resistor into
each pin. Machine Model: 200pF
capacitor discharged directly into each
pin.
ESD Classification per JESD22-A114C.01
for Human Body Model and JESD22-
A115 for Machine Model.
These specifications are guaranteed only
for the test conditions listed.
Units
Min
°C
-3
-4
-4
V
V
6
0.0414
±0.8
Typ
200
250
±2
11
10
10
1
Max
+3
+4
+4
25
April 2006 - 70A03207
aTS45C
mV/°C
Units
mV
µ A
µ A
µ A
°C
°C
°C
°C
°C
°C