ha13152 Renesas Electronics Corporation., ha13152 Datasheet
ha13152
Related parts for ha13152
ha13152 Summary of contents
Page 1
... HA13151, HA13152 14 W 4-Channel BTL Power IC Description The HA13151/HA13152 are high output and low distortion 4 ch BTL power IC designed for digital car audio load, this power IC provides output power 14 W with 10% distortion. Functions 4 ch BTL power amplifiers Built-in standby circuit Built-in muting circuit Built-in protection circuit (surge, T ...
Page 2
... HA13151, HA13152 Block Diagram Absolute Maximum Ratings (Ta = 25°C) Item Symbol 2 Rating Unit Remarks ...
Page 3
... Operating temperature Topr Storage temperature Tstg Notes: 1. Tolerance within 30 seconds 2. Tolerance in surge pulse waveform 3. Value per 1 channel 4. Value when attached on the infinite heat sink plate °C. The derating carve is as shown in the graph below. HA13151, HA13152 18 CC (DC (PEAK ...
Page 4
... HA13151, HA13152 Electrical Characteristics (V 25°C) HA13151 Item Symbol Quiescent current Output offset voltage V Q Gain G V Gain difference between G V channels Rated output power Po Max output power Pomax Total harmonic distortion T.H.D. Output noise voltage WBN Ripple rejection SVR Channel cross talk C ...
Page 5
... Standby current Standby control voltage V STH (high) Standby control voltage V STL (low) Muting control voltage V MH (high) Muting control voltage V ML (low) Muting attenuation ATTM HA13151, HA13152 Min Typ Max Unit — 270 — mA –300 0 +300 mV 38.5 40 41.5 dB –1.5 0 +1.5 dB — ...
Page 6
... HA13151, HA13152 Pin Explanation Pin No. Symbol Functions 1 IN1 CH1 INPUT 11 IN2 CH2 INPUT 13 IN3 CH3 INPUT 23 IN4 CH4 INPUT 2 STBY Standby control 3 OUT1 + CH1 OUTPUT 5 OUT1 – 7 OUT2 + CH2 OUTPUT 9 OUT2 – 15 OUT3 + CH3 OUTPUT 17 OUT3 – 19 OUT4 + CH4 OUTPUT 21 OUT4 – ...
Page 7
... Power of input stage CC 4 CH1 GND CH1 power GND 8 CH2 GND CH2 power GND 16 CH3 GND CH3 power GND 20 CH4 GND CH4 power GND 12 IN GND Input signal GND HA13151, HA13152 Input DC Impedance Voltage Equivalence Circuit — — CC — V — CC — ...
Page 8
... HA13151, HA13152 Point of Application Board Design 1. Notes on Application Board’s Pattern Design For increasing stability, the connected line of V lower impedance. For increasing stability better to place the capacitor between V IC. For increasing stability better to place and R1 to R8, which are for stopping oscillation, close to IC ...
Page 9
... We recommend value of capacitor greater then 1 µF. Also transitional popping noise can be reduced sharply by muting before V ON/OFF. Figure 2 How to use Muting Circuit Table 1 Muting ON/OFF Time C (µF) ON Time nothing under 1 µ HA13151, HA13152 and Standby are CC OFF Time under 1 µ ...
Page 10
... HA13151, HA13152 10 ...
Page 11
... HA13151, HA13152 11 ...
Page 12
... HA13151, HA13152 12 ...
Page 13
... HA13151, HA13152 13 ...
Page 14
... HA13151, HA13152 14 ...
Page 15
... HA13151, HA13152 15 ...
Page 16
... HA13151, HA13152 16 ...
Page 17
... HA13151, HA13152 17 ...
Page 18
... HA13151, HA13152 18 ...
Page 19
... HA13151, HA13152 19 ...
Page 20
... HA13151, HA13152 20 ...
Page 21
... HA13151, HA13152 21 ...
Page 22
... HA13151, HA13152 22 ...
Page 23
... HA13151, HA13152 23 ...
Page 24
... HA13151, HA13152 When using this document, keep the following in mind: 1. This document may, wholly or partially, be subject to change without notice. 2. All rights are reserved: No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without Hitachi’s permission. 3. Hitachi will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user’ ...