S3901_05 HAMAMATSU [Hamamatsu Corporation], S3901_05 Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
S3901_05
Manufacturer Part Number
S3901_05
Description
NMOS linear image sensor Current output, high UV sensitivity, excellent linearity, low power consumption
Manufacturer
HAMAMATSU [Hamamatsu Corporation]
Datasheet
1.S3901_05.pdf
(6 pages)
ACTIVE VIDEO OUTPUT
S3901/S3904 series do not require any DC voltage supply
for operation. However, the Vss, Vsub and all NC terminals
must be grounded. A start pulse φst and 2-phase clock pulses
φ1, φ2 are needed to drive the shift register. These start and
clock pulses are positive going pulses and CMOS logic com-
patible.
The 2-phase clock pulses φ1, φ2 can be either completely
separated or complementary. However, both pulses must not
be “High” at the same time.
A clock pulse space (X1 and X2 in Figure 7) of a “rise time/fall
time - 20” ns or more should be input if the rise and fall times
of φ1, φ2 are longer than 20 ns. The φ1 and φ2 clock pulses
must be held at “High” at least 200 ns. Since the photodiode
signal is obtained at the rise of each φ2 pulse, the clock pulse
frequency will equal the video data rate.
Figure 7 Timing chart for driver circuit
There are two methods for reading out the signal from an NMOS
linear image sensor. One is a current detection method using
the load resistance and the other is a current integration method
using a charge amplifier. In either readout method, a positive
bias must be applied to the video line because photodiode
anodes of NMOS linear image sensors are set at 0 V (Vss).
Figure 8 shows a typical video bias voltage margin. As the clock
pulse amplitude is higher, the video bias voltage can be set
larger so the saturation charge can be increased. The rise and
fall times of the video output waveform can be shortened if the
video bias voltage is reduced while the clock pulse amplitude is
still higher. When the amplitude of φ1, φ2 and φst is 5 V, setting
the video bias voltage at 2 V is recommended.
To obtain good linearity, using the current integration method is
advised. In this method, the integration capacitance is reset to
the reference voltage level immediately before each photodiode
is addressed and the signal charge is then stored as an integra-
tion capacitive charge when the address switch turns on. Fig-
ures 9 and 10 show a typical current integration circuit and its
pulse timing chart. To ensure stable output, the rise of a reset
pulse must be delayed at least 50 ns from the fall of φ2.
2
st
1
Signal readout circuit
Driver circuit
END OF SCAN
V s (H)
V s (L)
V 1 (H)
V 1 (L)
V 2 (H)
V 2 (L)
st
1
2
tpw s
tr s
t ov
tr 1
tpw 1
X1
tvd
tpw 2
tf s
tf 1
tr 2
NMOS linear image sensor
X2
tf 2
KMPDC0022EA
The amplitude of start pulse φst is the same as the φ1 and φ2
pulses. The shift register starts the scanning at the “High”
level of φst, so the start pulse interval determines the length of
signal accumulation time. The φst pulse must be held “High”
at least 200 ns and overlap with φ2 at least for 200 ns. To
operate the shift register correctly, φ2 must change from the
“High” level to the “Low” level only once during “High” level of
φst. The timing chart for each pulse is shown in Figure 7.
The end of scan (EOS) signal appears in synchronization
with the φ2 timing right after the last photodiode is addressed,
and the EOS terminal should be pulled up at 5 V using a 10
kΩ resistor.
Hamamatsu provides the following driver circuits and related
products (sold separately).
Figure 8 Video bias voltage margin
End of scan
10
8
6
4
2
0
4
S3901/S3904 series
CLOCK PULSE AMPLITUDE (V)
5
C7883,
C7884 series
C7883 to
C7885 series
6
VIDEO BIAS RANGE
7
8
MIN.
9
10
KMPDB0043EA