uwr-5-1600-d5a-c C&D Technologies., uwr-5-1600-d5a-c Datasheet - Page 3

• Manufacturer Part Number: uwr-5-1600-d5a-c
• Description: Single Output, High Reliability, 2 X 1 , 6-10 Watt, Dc/dc Converters
• Manufacturer: C&D Technologies.

Performance/Functional Specifications
Typical @ T
Input
Output
environmental
Physical
Input Voltage range:
Input Current
Input Filter type ➁
Overvoltage Shutdown:
reverse-Polarity Protection
V
temperature Coefficient
ripple/Noise (20MHz BW) ➁
line/load regulation
efficiency
Isolation Voltage ➂
Isolation Capacitance
Current limiting
Overvoltage Protection ➃
transient response (50% load step)
Switching Frequency
Flammability
Operating temperature (Ambient):
Storage temperature
Dimensions
Shielding
Case Connection:
Case Material
Pin Material
Weight
➀ These power converters require a minimum 10% loading to maintain specified regulation.
➁ Application-specific input/output filtering can be recommended and perhaps added
➂ Devices can be screened or modified for higher guaranteed isolation voltages.
➃ Except for 3.3V devices which have no protection.
Out
Dynamic Characteristics
D5A Models
D12A Models
D24E Models
D48A Models
D48E Models
D5A Models
D12A Models
D24E Models
D48A and D48E Models
Without Derating
With Derating
D5A, D12A and D24E Models
D48A and D48E Models
Operation under no-load conditions will not damage these devices; however they may
not meet all listed specifications.
internally upon request for scheduled, quantity orders. Contact DATEL Applications
Engineering for details.
Contact DATEL Applications Engineering for details.
accuracy (50% load)
A
= +25°C under nominal line voltage and full-load conditions, unless noted.
4.7-7.25 Volts (5V nominal)
9-18 Volts (12V nominal)
18-36Volts (24V nominal
18-75 Volts (48V nominal)
36-72 Volts (48V nominal)
See Ordering Guide
Pi
None
20 Volts
40 Volts
76 Volts
Yes (Instantaneous, 6A maximum)
±1%, maximum
±0.02% per °C
See Ordering Guide
See Ordering Guide
See Ordering Guide
1500Vdc, guaranteed
250pF
Auto-recovery
Zener/transorb clamp, magnetic feedback
200µsec max. to ±1.5% of final value
165kHz (±15kHz)
UL94V-0
–40 to +60/65/70°C (Model dependent)
to +100°C (See Derating Curves)
–40 to +105°C
2" x 1" x 0.375" (51 x 25 x 9.5mm)
5-sided
Pin 2 (–V
Pin 1 (+V
Corrosion resistant steel with
non-conductive, epoxy-based, black
enamel finish and plastic baseplate
Gold plate over copper alloy
1.3 ounces (37 grams)
www.murata-ps.com
IN
IN
)
)
Single Output, High Reliability, 2" x 1", 6-10 Watt, DC/DC Converters
➀
Floating Outputs
Since these are isolated DC/DC converters, their outputs are "floating."
Designers will usually use the output Common (pin 5) as the ground/return
of the load circuit. You can, however, use the +Output (pin 3) as ground/
return to effectively reverse the output polarity.
Filtering and Noise reduction
All A-Series UWR 6-10 Watt DC/DC Converters achieve their rated ripple
and noise specifications without the use of external input/output capaci-
tors. In critical applications, input/output ripple and noise may be further
reduced by installing electrolytic capacitors across the input terminals and/
or low-ESR tantalum or electrolytic capacitors across the output terminals.
The caps should be located as close to the power converters as possible.
Typical values are listed in the tables below. In many applications, using
values greater than those listed will yield better results.
In critical, space-sensitive applications, DATEL may be able to tailor the
internal input/output filtering of these units to meet your specific require-
ments. Contact our Applications Engineering Group for additional details.
absolute Maximum ratings
t e C h N I C a l N O t e S
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in
the Performance/Functional Specifications Table is not implied.
Input Voltage:
Input reverse-Polarity Protection
Output Overvoltage Protection
Output Current
dent.
Storage temperature
to reduce Input ripple
to reduce Output ripple
D5A Models
D12A Models
D24E Models
D48A and D48E Models
5/5.2V Outputs
12V Outputs
15V Outputs
short-circuit duration model
D5A Models
D12A and D24E Models
D48A and D48E Models
5/5.2V Outputs
12/15V Outputs
technical enquiries email: [e-mail], tel:
47µF, 10V
20µF, 50V
10µF, 100V
47µF, 10V, Low ESR
22µF, 20V, Low ESR
MDC_uWr6-10W Series.B02 Page 3 of 6
10 Volts
22 Volts
44 Volts
80 Volts
Current must be <6A. Brief
duration only. Fusing recommended.
6.8 Volts, limited duration
15 Volts, limited duration
18 Volts, limited duration
Current limited. Max. current and
–40 to +105°C
uWr Series
[phone]
depen-