L2000-26-2 ARTESYN [Artesyn Technologies], L2000-26-2 Datasheet - Page 3

• Manufacturer Part Number: L2000-26-2
• Description: Single output 2000 Watt AC/DC high current power supplies
• Manufacturer: ARTESYN [Artesyn Technologies]

Air Venting
Surface
(127.0)
(203.2)
5.00
8.00
PIN NO.
PAGE 3
2000W AC/DC
2000 Watt
AC/DC high current power supplies
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
(19.05)
(5.08)
(101.60)
.50 (12.7)
(146.05)
.20
.75
(28.45)
4.00
5.75
1.12
DC OK Inverse (Optional)
AC Good Inverse
+ Remote Sense
Inhibit (Optional)
- Remote Sense
- Remote Sense
Current Monitor
Remote Adjust
OUTPUT PIN CONNECTIONS
Current Share
Supply Fault
Margin High
Margin Low
ALL DIMENSIONS IN INCHES (mm)
AC Good
DC OK
Enable
J1
AIRFLOW
(171.45)
8-32 X .20 (5.08) Deep Max.
(4) Mounting Both Sides
6.750
12.45 MAX
(316.23)
|
MEDIUM TO HIGH POWER AC/DC POWER SUPPLIES
Notes 3 & 4, Fig. 2 & 5
Notes 3 & 4, Fig. 2 & 5
Notes 2 & 4, Fig. 1
Notes 3 & 4, Fig. 2
Notes 3 & 4, Fig. 2
Notes 2 & 4, Fig. 1
(279.4)
11.00
REFERENCE
Notes 5 & 6
Note 1
Note 1
Note 3
Note 6
Note 6
Fig. 3
Fig. 4
Air Venting
Surface
8-32 X .20 (5.08) Deep Max.
(4) Top and Bottom Mounting
.19 X .70 X 1.20 LG
(4.83 X 17.78 X 30.48)
Output Bars
5/16 X 1.00 Bolt Washer and
Nut Supplied
(10.16)
Mechanical notes
A AC connector is 3 position terminal block (#8 screws included), mating to
B DC output is 5/16-18 studs mating to 5/16 terminal lugs.
C J-1 signal connector is Molex 39-30-1140 or equivalent. Mating
D J-2 signal connector is Molex 39-01-1120 or equivalent. Mating
E Signal connector contacts are Molex 39-00-0039 or equivalent.
F Auxiliary DC output(s) are 6 position terminal block (#8 screws included)
G TB1 and J2 are not installed on single output models.
Output pin connector notes
1
2
3
4
5
6
.40
Ø.136
(3.45)
#8 ring tongue terminal.
connector is Molex 39-01-2140 or equivalent.
connector is 39-01-2120 or equivalent.
mating to #8 ring tongue terminal.
Use 20AWG or larger twisted pair.
Switch on voltage must be <0.5V @ 5mA.
Figure 2 transistor on when signal TRUE. On voltage is <0.5V @ 5mA.
VCC in figures 1 and 2 is supplied internally; ground is pin 15.
Overvoltage and overtemperature will force fault TRUE. On voltage is
<0.5V @ 5mA.
All I/O signals are referenced to pin 15.
2
AC Input Terminal Block
(# 8 Screws)
1Ø INPUT
(203.2)
8.00
(19.81)
.78
VOLTAGE
ADJ
OUTPUT
GOOD
J1
Signal Connector
15 Position D-Sub
With Socket Contacts
(12.19)
.48
(47.75)
(64.52)
1.88
2.54
(127.0)
5.00
Voltage Adjust
Good LED's
and Output
PIN 1