VS-500A VECTRON [Vectron International, Inc], VS-500A Datasheet
VS-500A
Related parts for VS-500A
VS-500A Summary of contents
Page 1
... Smoothing and Frequency Translation • 10 Gigabit Ethernet Clock Smoothing • Frequency Translation Description The VS-500A is a SAW based voltage controlled oscillator that operates at the fundamental frequency of the internal SAW filter. This resonator is a high-Q quartz device that enables the circuit to achieve low phase jitter performance over a wide operating temperature range ...
Page 2
... VS-500A Voltage Controlled SAW Oscillator Pin Information Table 1. Pin Function Pin Symbol GND 4 Output 5 COutput setting OD low, the outputs are disabled and OUT is held high while Complementary OUT is held low. The threshold for Output Disable is 1.4V above pin 3. Output Disable should not be driven above mid supply and during normal operation, should be left floating (use with an open collector or 3-State gate for interfacing with standard logic) ...
Page 3
... PLL Gnd 3 Note 2: To diasble output, connect Output Disable to ground. To enable output, leave pin 2 floating or open. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON VS-500A Voltage Controlled SAW Oscillator +5.0V +5.0V +5.0V .01uF .1uF 120 Vcc ...
Page 4
... VS-500A Voltage Controlled SAW Oscillator Vc (From PLL) OD 0.1uF Gnd .01uF -5.0V Vc (From PLL) OD 0.1uF Gnd .01uF -5.0V Note 2: To diasble output, connect Output Disable to –5V. To enable output, leave pin 2 floating or open. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON ...
Page 5
... Storage Temperature Soldering Temp./Time 1 Limts beyond which performance can not be guaranteed. 2 Limits beyond which device life may be impaired. Qualification Conformance The VS-500A family passes the following Mil-Std qualification. Table 5. Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Vectron International • ...
Page 6
... The time above 183°C should not exceed 60 seconds and the peak temperature should be no more than 220°C for 10 seconds. The VS-500A’s are 100% screened for hermiticity so an aqueous wash is not an issue. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON 6 Table 6 ...
Page 7
... Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON VS-500A Voltage Controlled SAW Oscillator Figure 6. Outline Diagram Dimensions are in inches and (millimeters) 0.200 (5.08) 0.100 (2.54) 0.346 (8.80) Figure 7. Suggested Pad Layout 0.118 (3.00) 0.050 (1.27) ...
Page 8
... VS-500A Voltage Controlled SAW Oscillator Table 7. Tape and Reel Dimensions (mm) Tape Dimensions Product VS-500A 24 11.5 1.5 Ordering Information Table 8. Available Frequencies (MHz) 155.520 177.7371 625. 000 669.1281 759.410 Other frequencies available upon request www.vectron.com Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. ...