CMP350-9601 ARTESYN [Artesyn Technologies], CMP350-9601 Datasheet - Page 4

• Manufacturer Part Number: CMP350-9601
• Description: Quad output 350 Watt AC/DC high wattage power supplies with PFC
• Manufacturer: ARTESYN [Artesyn Technologies]

FEATURES
Current share
(See Note 12)
Power OK
(See Note 13)
Remote-sense
System inhibit
Power fail detect
(See Note 13)
TRIMAUX2 is connected to
AUX1SET by a factory fitted
jumper to ensure CH. 1
regulates at the nominal
set voltage
Aux. 1 channel trim connections. (-9601, -9602, -9603, 9606)
AUX1SET
TRIMAUX2
Aux. 2 channel trim connections (-9604, -9692)
Aux. 1 channel trim connections (-9604, -9692)
AC/DC high wattage power supplies with PFC
POWER GOOD SIGNAL
12CH2
TRIMAUX
GND2
12CH1
TRIMAIN
GND1
EXTERNAL OUTPUT TRIMMING
PFD SIGNAL
Main channel trim connections
AC INPUT
OUTPUT
DOWN
DOWN
TRIM
TRIM
Forced
Asserted Low
0.4V
Asserted high
Asserted low
t1 Varies with line and load
t2
t1 + t2
http://www.artesyn.com
4ms
GND3
TRIMAUX2
TRIM
UP
TRIM
UP
20ms
To trim CH1, remove the
jumper and connect a resistor
between GND3
and TRIMAUX2
LOW TO MEDIUM POWER AC/DC POWER SUPPLIES
t1
TRIM
UP/DOWN
TRIM
UP/DOWN
auxiliary 1 if 5V or 3.3V
auxiliary 1 if 5V or 3.3V
t2
Indicates loss of AC
Main output >75%
Inhibits all outputs
Main output and
Main output and
(14)
4ms warning
TRIM
UP/DOWN
Notes
1
2
3
4
5
6
7
8
9
10 A minimum of 300LFM of forced air cooling is required for proper
11 All outputs must be derated linearly from maximum specified loads during
12 Current share is a single wire share circuit that allows the main output on
13 The power fail detect and power OK signals are open-collector outputs
14 Connection from TRIMAUX2 to AUX1SET causes the output for Ch. aux. 1
15 3 orthogonal axes, random vibration, 10 minute test per axes.
16 This product is only for inclusion by professional installers within other
The unit must be powered up into the recommended minimum loads to
ensure the outputs come up.
Combined maximum output power for Aux. 1, 2 and 3 is 220W.
For models -9604 and -9692, on the aux 1 channel, output ripple and
noise is measured 6 inches down the output cables through a 1 foot long
twisted pair terminated with a parallel combination of a 10µF electrolytic
and a 0.1µF ceramic capacitors. For all other channels on all models,
ripple and noise is measured directly at the output terminals.
No shutdown or latch-up occurs; voltage is internally limited to specified
range.
Aux. 2 tracks Aux. 3, Aux. 4 not adjustable.
Aux. 3 tracks Aux. 2.
Output is not adjustable.
CMP350-9604 rated operation:
The auxiliary channels must share power as indicated by graph 1.
The maximum output power is 220W.
CMP350-9692 rated operation:
The auxiliary channels must share power as indicated by graph 2.
The maximum output power is 220W.
operation of the CMP350.
operation above 50
multiple CMP350 units to be operated in parallel. Auxiliary channels share
on -9604 and -9692 models by connecting the CSAUX channel.
which will sink 40mA or less in the low state and should be pulled up to a
bias voltage with an appropriately sized resistor.
The system inhibit and output inhibit signals require a current source to be
asserted high.
on models -9604 and -9692 to regulate at its nominal factory set voltage.
equipment and must not be operated as a stand alone product.
Sum of 12V
Sum of 12V
Channel
Loads*
Channel
Loads*
VOH
VOL
IOL
VIH
IIH
°
C.
15A
10A
15A
10A
5A
0A
5A
0A
Graph 1
Graph 2
* Max. load for AUX2 is 10A
* Max. load for AUX2 is 10A
Max load for AUX3 is 5A
Min.
Min.
3.5V
0mA
Max load for AUX3 is 5A
0V
0A
4V
OPERATION
5A
3.3 V Channel Load
OPERATION
5A
5V Channel Load
RATED
RATED
8A
8A
10A
10A
|
-40mA
-10mA
15.0V
Max.
Max.
0.4V
40V
350 Watt
15A
350W AC/DC
15A
10A
20A
10A
PAGE 65
1