CM3002-18 CALMIRCO [California Micro Devices Corp], CM3002-18 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
CM3002-18
Manufacturer Part Number
CM3002-18
Description
Micropower 1.0A Low Dropout CMOS Regulators
Manufacturer
CALMIRCO [California Micro Devices Corp]
Datasheet
1.CM3002-18.pdf
(17 pages)
Performance Information (cont’d)
Typical Thermal Characteristics
The overall junction to ambient thermal resistance
(
rily of two paths in series. The first path is the junction
to the case (
and the second path is case to ambient (
resistance which is dependent on board layout. The
final operating junction temperature for any set of con-
ditions can be estimated by the following thermal equa-
tion:
The CM3002 family uses thermally enhanced SOIC
and MSOP packages where all the GND pins (5
through 8) are integral to the leadframe. When this
package is mounted on a double sided printed circuit
board with two square inches of copper allocated for
“heat spreading”, the resulting θ
the SOIC package and 70° C/W for the MSOP pack-
age.
Based on a maximum power dissipation of 0.8W (Load
x Vin-Vout = 1.0A x [3.3V-2.5V]) with an ambient of
70° C, the resulting junction temperature for a SOIC-
packaged device will be:
© 2004 California Micro Devices Corp. All rights reserved.
14
θ
JA
430 N. McCarthy Blvd., Milpitas, CA 95035-5112 ▲ Tel: 408.263.3214
) for device power dissipation (P
T
JUNC
T
JUNC
θ
JC
= T
= T
1.54
1.52
1.50
1.48
1.46
) which is defined by the package style,
Output Voltage with Temperature (5mA Load)
= T
= 70° C + 0.8W ∗ (50° C/W)
= 70° C + 40° C = 110° C
AMB
AMB
0
AMB
+ P
+ P
+ P
Junction Temperature [°C]
25
D
D
Figure 1. CM3002-15SA/SF Performance vs. Temperature
∗ (θ
D
∗ (θ
∗ (θ
JA
JC
JA
50
JA
)
) + P
is about 50° C/W for
)
D
) consists prima-
75
D
∗ (θ
θ
CA
CA
100
) thermal
)
125
Thermal characteristics were measured using a double
sided board with two square inches of copper area
connected to the
Measurements showing performance up to a junction
temperature of 125° C are presented in
Figure
under light load conditions (5mA); this allows the ambi-
ent temperature to be representative of the internal
junction temperature.
Note: The use of multi-layer board construction with
separate ground and power planes will further enhance
the overall thermal performance. In the event of no
copper area being dedicated for heat spreading, a
multi-layer board construction using only the minimum
size pad layout will typically provide a CM3002 device
packaged in a SOIC package with an overall θ
50° C/W, which allows up to 0.8W to be dissipated
safely.
Please consult CAMD Technical Support for assistance
with thermal analysis of the CM3002 family of regula-
tors with respect to a specific application.
700
600
500
400
300
200
100
Ground Current with Temperature (No Load)
0
▲ Fax: 408.263.7846
2,
0
Figure 3
Junction Temperature [°C]
25
GND
and
50
pins for “heat spreading”.
Figure
75
▲
4. They were performed
www.calmicro.com
100
125
CM3002
Figure
JA
08/16/04
1,
of