CS2012C0G104B100NBA SAMWHA [SAMWHA ELECTRIC], CS2012C0G104B100NBA Datasheet - Page 9

• Manufacturer Part Number: CS2012C0G104B100NBA
• Description: Multi Layer Ceramic Capacitors
• Manufacturer: SAMWHA [SAMWHA ELECTRIC]

SAMWHA CAPACITOR CO., L TD offers a line of MLCC(Multilayer Ceramic Capacitor).
These parts are rated at 3kV dc and safety approved and certified to UL
(Underwriters Laboratories Inc.
20
SAMWHA CAPACITOR Co., Ltd.
)
Reliability and Test Conditions(General Type)
No.
3
6
7
2
4
5
1
Operating
Temperature Range
Insulation Resistance
Dielectric Strength
Capacitance
Dissipation Factor
Solderability of
Termination
Resistance
to
Soldering
Heat
Item
Appearance
Capacitchange Within ±2.5% or ±0.25㎊ X7R, X5R : ≤ ±7.5%
Dissipation
Factor
(or Q)
I.R.
Compensating Type
C0G : -55 to +125℃
More than 10,000
No defects or abnormalities
Within the specified tolerance
30㎊ Min. :
Q≥1,000 (DF≤0.1%)
30㎊ Max. :
Q≥400+20C
(DF≤1/(400+20C))
Termination should be covered with more than
75% of new solder
No marked defect
(whichever is larger)
More than 10,000
30㎊ Min. :
Q≥1,000 (DF≤0.1%)
30㎊ Max. :
Q≥400+20C
(DF≤1/(400+20C))
Temperature
MΩ
MΩ
or 500
or 500
Characteristic
X7R : -55 to +125℃ X5R : -55 to +85℃
Y5V : -30 to +85℃
Y5V
Char. 50V Min. 25V
Char. 50V Min. 25V
X7R ≤2.5%/ ≤3%/ ≤3.5%/ ≤5%/ ≤5%/
X5R
Y5V
X7R ≤2.5%/ ≤3%/ ≤3.5%/ ≤5%/
X5R
Y5V
Ω F
Ω .F
High Dielectric Constant Type
You can check the specification at
the appendix for each product
with mark
≤5%/
≤5%/ ≤7%/
(Whichever is smaller)
≤5%
≤9%
≤5%
≤9%
(Whichever is smaller)
: ≤ ±20%
≤7%/
≤7%
≤9%
≤7%
≤9% ≤12.5%
≤9%
≤9% ≤12.5%/
≤12.5% ≤15%
16V
16V
≤7%
≤7%
≤12.5%/
≤10%
10V
≤10% ≤10%
≤15%
10V
Multi Layer Ceramic Capacitors
≤15%
≤5%/
≤15%
6.3V
6.3V
≤10%
- Pb-Free Type
- Pre-Heating
- C0G : The rated voltage×300%
- X7R, X5R, Y5V : 〃
- Applied between the terminations
- The charge/discharge current is
The capacitance/Q/D.F. should be
measured at 25℃ at the frequency
and voltage shown in the table.
- Preheat the capacitor at 120 to 150℃
- Soldering Temp. : 260±5℃
- Immersion Time : 10±0.5sec
- Initial measurement
- Measurement after test
- Applied the rated voltage for 2
- The charge/discharge current is
C0G
(C≤1000pF)
C0G
(C >1000pF)
X7R, X5R, Y5V
(C≤10㎌
6.3V Min.)
X7R, X5R, Y5V
(C >10㎌)
Solder Temperature : 260±5℃
Immersion Time : 3±0.1sec
at 80~120℃ for 10~30sec
for 1 to 5 seconds.
Solder : 96.5Sn-3Ag-0.5Cu
for 1 minute. (Preheating for 3225,
4520, 4532 Step1 : 100℃ to 120℃, 1min
Step2 : 170℃ to 200℃, 1min) Immerse the
capacitor in a eutectic solder solution
Perform a heat treatment at 150+0, -10℃
for one hour and then let sit for 48±4
hours at room temperature.
Perform the intial measurement.
Take it out and set it for 24±2 hours
(temperature compensating type)
or 48±4 hours (high dielectric constant
type)then measure
less than 50mA.
less than 50mA.
minutes of charging.
Cap.
and Conditions
Test Methods
SMD Type
Frequency
1±0.1M㎐
1±0.1k㎐
1±0.1k㎐
120±24㎐
Testing
×250%
0.5±0.1Vrms
0.5 to 5Vrms
1±0.2Vrms
1±0.2Vrms
Voltage
Testing
21