mlp2n06cl ON Semiconductor, mlp2n06cl Datasheet - Page 3

• Manufacturer Part Number: mlp2n06cl
• Description: Smartdiscretes Mosfet 2 Amps, 62 Volts, Logic Level
• Manufacturer: ON Semiconductor

THE SMARTDISCRETES CONCEPT
and passive elements can be obtained that provide on−chip
protection to the basic power device. Such elements require
only a small increase in silicon area and/or the addition of one
masking layer to the process. The resulting device exhibits
significant improvements in ruggedness and reliability as
well as system cost reduction. The SMARTDISCRETES
device functions can now provide an economical alternative
to smart power ICs for power applications requiring low
on−resistance, high voltage and high current.
rugged power switching device with short circuit protection
that can be directly interfaced to a microcontroller unit
(MCU). Ideal applications include automotive fuel injector
driver, incandescent lamp driver or other applications where
a high in−rush current or a shorted load condition could occur.
OPERATION IN THE CURRENT LIMIT MODE
withstand the current stress resulting from a shorted load
before its maximum junction temperature is exceeded is
dependent upon a number of factors that include the amount
of heatsinking that is provided, the size or rating of the device,
its initial junction temperature, and the supply voltage.
Without some form of current limiting, a shorted load can
raise a device’s junction temperature beyond the maximum
rated operating temperature in only a few milliseconds.
shorted load powered by an automotive battery (10 to 14 V)
for almost a second if its initial operating temperature is under
100°C. For longer periods of operation in the current−limited
mode, device heatsinking can extend operation from several
seconds to indefinitely depending on the amount of
heatsinking provided.
From a standard power MOSFET process, several active
These devices are designed for applications that require a
The amount of time that an unprotected device can
Even with no heatsink, the MLP2N06CL can withstand a
6
5
4
3
2
1
0
−50
Figure 3. I
T
0
D(lim)
J
, JUNCTION TEMPERATURE (°C)
Variation With Temperature
50
100
V
V
GS
DS
= 5 V
= 10 V
http://onsemi.com
MLP2N06CL
150
3
SHORT CIRCUIT PROTECTION AND THE EFFECT OF
TEMPERATURE
integrated means of protecting the MOSFET component
from high in−rush current or a shorted load. As shown in the
schematic diagram, the current limiting feature is provided
by an NPN transistor and integral resistors R1 and R2. R2
senses the current through the MOSFET and forward biases
the NPN transistor’s base as the current increases. As the
NPN turns on, it begins to pull gate drive current through R1,
dropping the gate drive voltage across it, and thus lowering
the voltage across the gate−to−source of the power
MOSFET and limiting the current. The current limit is
temperature dependent as shown in Figure 3, and decreases
from about 2.3 A at 25°C to about 1.3 A at 150°C.
dissipate power during a shorted load condition, it is
important to provide sufficient heatsinking to limit the device
junction temperature to a maximum of 150°C.
power MOSFET’s on−resistance, but the effect of
temperature on the combination is less than on a standard
MOSFET due to the lower temperature coefficient of R2. The
on−resistance variation with temperature for gate voltages of
4 and 5 V is shown in Figure 5.
provide ESD protection to greater than 2 kV, HBM. This
on−chip protection feature eliminates the need for an external
Zener diode for systems with potentially heavy line transients.
The on−chip circuitry of the MLP2N06CL offers an
Since the MLP2N06CL continues to conduct current and
The metal current sense resistor R2 adds about 0.4 W to the
Back−to−back polysilicon diodes between gate and source
1.0
0.8
0.6
0.4
0.2
0
0
1
V
Figure 4. R
GS
2
, GATE−TO−SOURCE VOLTAGE (VOLTS)
Gate−To−Source Voltage
T
3
J
= −50°C
4
DS(on)
5
Variation With
25°C
6
100°C
7
I
8
D
= 1 A
9
10