mpm-10s-24is MicroPower Direct, LLC, mpm-10s-24is Datasheet

no-image

mpm-10s-24is

Manufacturer Part Number
mpm-10s-24is
Description
Board Mount, 10w Single & Dual Output Ac/dc Power Supplies
Manufacturer
MicroPower Direct, LLC
Datasheet
MPM-10IS
Key Features:
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Board Mount, 10W
Single & Dual Output
AC/DC Power Supplies
10W Output Power
Universal 85-265 VAC Input
EN 60950 Approved
Meets IEC Safety Class II
Industry Standard Pin-Out
Single and Dual Outputs
Meets EN55022 B
>300 kHour MTBF
Electrical Specifi cations
Specifi cations typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.
Parameter
Output Voltage
Output Current
Output Voltage Accuracy
Line Regulation
Load Regulation,
Load Regulation,
Ripple & Noise (20 MHz)
Hold-Up Time
Temperature Coeffi cient
Over Voltage Protection
Short Circuit Protection,
Overload Protection,
Input
Parameter
Input Voltage Range
Input Frequency
Input Current
Inrush Current
EMI
Output
General
Parameter
Isolation Voltage
Isolation Test Voltage
Isolation Resistance
EMI/RFI
EMC Compliance
Switching Frequency
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Reliability Specifi cations
Parameter
MTBF
Safety Standards
Safety Approvals
Safety Class
Single Output
Dual Output
Note 4
Note 3
www.micropowerdirect.com
Series
Input to Output, Flash Tested For 60S
Electrical Fast Transients/Bursts On Mains
MIL HDBK 217F, 25°C, Gnd Benign
Electrostatic Discharge (ESD)
Conditions
Conditions
Conditions
Conditions
Conditions
3.3V & 5.0 VDC Output
RF Field Susceptibility
RH, Non-condensing
Free Air Convection (See Derating Curve)
Zener Diode Clamp
Typ. 120% to 180% of Output Power
Meets CISPR Pub. 22/FCC Class B
All Other Outputs
V
I
I
115 VAC, 60 Hz
IN
Input to Output
O
O
See Model Selection Guide
See Model Selection Guide
See Model Selection Guide
= Min to Max
= Min to Max
= Min to Max
Continuous (Autorecovery)
Conducted
2.52 x 1.77 x 0.75 Inches (64.0 x 45.0 x 19.0 mm)
IEN 60950, IEC 60950
IEN 60950, IEC 60950
500 VDC
115 VAC
230 VAC
Non-Conductive Plastic& Fiberglass (UL94-V0)
IEC 61140 Class II
Ambient
Surge IEC/EN 61000-4-5 Level 3 1kV/2 kV
3,000
4,700
Min.
Min.
Min.
Min.
Min.
100
300
-25
-40
85
47
IEC/EN 61000-4-4 Level 3 2 kV
IEC/EN 61000-4-2 Level 3
±0.02
Typ.
10.0
20.0
Typ.
±1.0
±0.5
±0.5
±2.5
Typ.
EN 55022 Level B
IEC/EN61000-4-3
Typ.
Typ.
120
100
+25
1.5
0.8
20
Max.
Max.
Max.
Max.
Max.
±2.0
±1.0
±1.0
±5.0
265
440
+71
+85
1.8
1.0
95
3.23 Oz (92g)
%V
% of V
kHours
mSec
Units
Units
%/°C
Units
Units
Units
P-P
A Pk
VAC
VAC
VAC
kHz
M
Hz
°C
°C
%
%
%
%
%
of V
O
O

Related parts for mpm-10s-24is

mpm-10s-24is Summary of contents

Page 1

... MPM-10IS Board Mount, 10W Single & Dual Output AC/DC Power Supplies Electrical Specifi cations Key Features: Specifi cations typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input • ...

Page 2

... VAC VAC MPM-10S-03IS 0.137 0.075 MPM-10S-05IS 0.199 0.075 MPM-10S-12IS 0.191 0.075 MPM-10S-15IS 0.191 0.075 MPM-10S-24IS 0.190 0.075 MPM-10D-12IS 0.172 0.075 MPM-10D-15IS 0.169 0.075 Other output combinations are available Contact the factory for details at: sales@micropowerdirect.com Notes Load regulation is measured for an output change 100% at nominal input line ...

Related keywords