hcts374t Intersil Corporation, hcts374t Datasheet

hcts374t

Manufacturer Part Number

hcts374t

Description

Radiation Hardened Octal D-type Flip-flop, Three-state, Positive Edge Triggered

Manufacturer

Intersil Corporation

Datasheet

1.HCTS374T.pdf (3 pages)

Current page: 1 of 3
Download datasheet (103Kb)

Radiation Hardened Octal D-Type

Flip-Flop, Three-State, Positive Edge

Triggered

Intersil’s Satellite Applications Flow

tested and guaranteed to 100kRAD total dose. These QML

Class T devices are processed to a standard ﬂow intended

to meet the cost and shorter lead-time needs of large

volume satellite manufacturers, while maintaining a high

level of reliability.

The Intersil HCTS374T is a Radiation Hardened Non-

Inverting Octal D-type, Positive Edge Triggered Flip-Flop

with three-state outputs. The eight ﬂip-ﬂops enter data into

their registers on the LOW-to-HIGH transition of the clock

(CP). Data is also transferred to the outputs during this

transition. The output enable (OE) controls the three-state

outputs and is independent of the register operation. When

the output enable is high, the outputs are in the high

impedance state.

Speciﬁcations

Speciﬁcations for Rad Hard QML devices are controlled by

the Defense Supply Center in Columbus (DSCC). The SMD

numbers listed below must be used when ordering.

Detailed Electrical Speciﬁcations for the HCTS374T are

contained in SMD 5962-95748. A “hot-link” is provided from

our website for downloading.

www.intersil.com/spacedefense/newsafclasst.asp

Intersil’s Quality Management Plan (QM Plan), listing all

Class T screening operations, is also available on our

website.

www.intersil.com/quality/manuals.asp

Ordering Information

NOTE:

distribution, or 450 units direct.

5962R9574801TRC

5962R9574801TXC

ORDERING

Minimum order quantity for -T is 150 units through

NUMBER

HCTS374DTR

HCTS374KTR

NUMBER

PART

Data Sheet

(SAF) devices are fully

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

-55 to 125

RANGE

TEMP.

(

Features

• QML Class T, Per MIL-PRF-38535

• Radiation Performance

• 3 Micron Radiation Hardened SOS CMOS

• Fanout (Over Temperature Range)

• Signiﬁcant Power Reduction Compared to LSTTL ICs

• DC Operating Voltage Range: 4.5V to 5.5V

• LSTTL Input Compatibility

• Input Current Levels Ii

Pinouts

www.intersil.com or 407-727-9207

- Gamma Dose ( ) 1 x 10

- Latch-Up Free Under Any Conditions

- SEP Effective LET No Upsets: >100 MEV-cm

- Single Event Upset (SEU) Immunity < 2 x 10

- Bus Driver Outputs - 15 LSTTL Loads

- V

GND

Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.

Errors/Bit-Day (Typ)

= 0.8V Max

= V

CC/2

HCTS374T (FLATPACK), CDFP4-F20

July 1999

HCTS374T (SBDIP), CDIP2-T20

GND

Min

TOP VIEW

5mA at V

RAD(Si)

File Number 4627.1

HCTS374T

, V

Intersil Corporation 1999

-9

/mg

Related parts for hcts374t

hcts374t Summary of contents

Page 1

... The Intersil HCTS374T is a Radiation Hardened Non- Inverting Octal D-type, Positive Edge Triggered Flip-Flop with three-state outputs. The eight ﬂip-ﬂops enter data into their registers on the LOW-to-HIGH transition of the clock (CP) ...

Page 2

... =High Level (Steady State). L =Low Level (Steady State). X =Immaterial. Z =High Impedance. = Transition from Low to High Level. Q0 =The level of Q before the indicated input conditions were established. 2 HCTS374T COMMON CONTROLS TRUTH TABLE INPUTS ...

Page 3

... No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 3 HCTS374T PASSIVATION: Type: Silox (S Thickness: 13k WORST CASE CURRENT DENSITY: < 2.0e5 A/cm TRANSISTOR COUNT: 468 PROCESS: CMOS SOS HCTS374T (3) (2) (1) (20) (19) (8) (9) ...

Related keywords

hcts374t datasheet
hcts374t data sheet
hcts374t pdf datasheet
hcts374t component
hcts374t part
hcts374t distributor
hcts374t RoHS
hcts374t datasheet download