gwixp425bdt Intel Corporation, gwixp425bdt Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/3/337/intel_corporation_sml.jpg)
gwixp425bdt
Manufacturer Part Number
gwixp425bdt
Description
Intel Xp42x Product Line Of Network Processors And Ixc1100 Control Plane Processor
Manufacturer
Intel Corporation
Datasheet
1.GWIXP425BDT.pdf
(134 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GWIXP425BDT
Manufacturer:
INTEL
Quantity:
48
Intel
Table 18.
Table 19.
March 2005
48
®
IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor
System Interface
Power Interface (Sheet 1 of 2)
BYPASS_CLK
SCANTESTMODE_N
RESET_IN_N
PWRON_RESET_N
HIGHZ_N
PLL_LOCK
RCOMP
1.
2.
†
††
VCC
VCCP
VSS
VCCOSCP
VSSOSCP
†
Name
Name
While PWRON_RESET_N is deasserted use Power On Reset column for the pin state.
After deassertion of PWRON_RESET_N, and deassertion of RESET_IN_N, and assertion of
PLL_LOCK, all signals reflect the value shown in the RESET column.
For a legend of the Type codes, see
IMPORTANT NOTE: When a system-level reset is asserted to the Intel
Network Processors and IXC1100 Control Plane Processor — either via a power-on reset, a system
reset, or a Watchdog-Timer reset — and any interface is in an active transaction (particularly the PCI
bus or expansion bus, but not precluding any interface), an illegal protocol is generated. The behavior
of the IXP42X product line and IXC1100 control plane processors is undefined in this situation and a
reset of other attached devices may be required.
For a legend of the Type codes, see
Type
I
I
I
I
Document Number: 252479, Revision: 005
†
††
1.3-V power supply input pins used for the internal logic.
3.3-V power supply input pins used for the peripheral (I/O) logic.
Ground power supply input pins used for both the 3.3-V and the 1.3-V power supplies.
3.3-V power supply input pins used for the peripheral (I/O) logic of the analog
oscillator circuitry.
Require special power filtering circuitry. Refer to
Ground input pins used for the peripheral (I/O) logic of the analog oscillator circuitry.
Used in conjunction with the VCCOSCP pins.
Requires special power filtering circuitry. Refer to
Reset
Power
On
H
H
Z
0
0
Z
1
Reset
VI/PE
VI/PE
VO
VI
VI
VI
2
Type
Table 5 on page
Table 5 on page
O
I
I
I
I
I
I
†
Used for test purposes only.
Must be pulled high for normal operation.
Used for test purposes only.
Must be pulled high for normal operation.
Used as a reset input to the device after power up
conditions have been met. Power up conditions include
the power supplies reaching a safe stable condition and
the PLL achieving a locked state and the
PWRON_RESET_N coming to an active state prior to
the RESET_IN_N coming to an active state.
Signal used at power up to reset all internal logic to a
known state after the PLL has achieved a locked state.
The PWRON_RESET_N input is a 1.3-V tolerant only.
Used for test purposes only.
Must be pulled high for normal operation.
Signal used to inform external reset logic that the
internal PLL has achieved a locked state.
Signal used to control PCI drive strength characteristics.
Drive strength is varied on PCI address, data and
control signals.
Pin requires a 34-: +/- 1% tolerance resistor to ground.
Refer to
Description
33.
33.
Figure 13 on page
Figure 11 on page 84
Figure 11 on page 84
Description
®
IXP42X Product Line of
85.
Datasheet