gwixp465bad ETC-unknow, gwixp465bad Datasheet - Page 136
![no-image](/images/no-image-200.jpg)
gwixp465bad
Manufacturer Part Number
gwixp465bad
Description
Network Proc 1.3v/1.4v/2.5v/3.3v 400mhz 544-pin Bga
Manufacturer
ETC-unknow
Datasheet
1.GWIXP465BAD.pdf
(148 pages)
- Current page: 136 of 148
- Download datasheet (2Mb)
Table 75.
Figure 40.
Intel
Datasheet
136
®
IXP45X and Intel
HPI*-16 Non-Multiplexed Read Mode
HPI-16 Non-Multiplexed Read Accesses Values
Notes:
1.
2.
3.
4.
5.
6.
7.
T
T
T
T
Symbol
cs2hds1val
hds1_pulse
data_setup
add_setup
T
®
recov
IXP46X Product Line of Network Processors
EX_ADDR[23:0]
The address phase parameter (T1) must be set to a minimum value of 2. This value allows three T
clocks for the address phase. This setting is required to ensure that in the event of an HRDY, the
IXP45X/IXP46X network processors have had sufficient time to recognize the HRDY and hold the
address phase for at least one clock pulse after the HRDY is de-active.
The data setup phase parameter (T2) must be set to a minimum value of 2. This value allows three T
clocks for setup phase.
The data strobe phase parameter (T3) must be set to a minimum value of 1. This value allows two T
clocks for the data phase. This setting is required to ensure that in the event of an HRDY, the IXP45X/
IXP46X network processors have had sufficient time to recognize the HRDY and hold the data setup
phase for at least one clock pulse after the HRDY is de-active
Setting the recovery phase parameter (T5) will adjust the duration between successive accesses on
the Expansion Bus interface.
HRDY can be asserted by the DSP at any point in the access. The interface will not leave states T1 or
T3 until HRDY is de-active
One cycle is the period of the Expansion Bus clock.
Timing was designed for a system load between 5pF and 60pF for high drive setting
EX_RDY_N
EX_WR_N
EX_RD_N
EX_CS_N
EX_DATA
(hds1_n)
(hr_w_n)
EX_CLK
(hcs_n)
(hdout)
Valid time that address is asserted on the line. The address is
asserted at the same time as chip select.
Delay from chip select being active and the HDS1 data strobe
being active.
Pulse width of the HDS1 data strobe
Data is valid from the time from of the falling edge of
HDS1_N to when the data is read.
Time required between successive accesses on the expansion
interface.
(hrdy)
Tcs2hds1val
(ha)
Intel
®
IXP45X and Intel
T1
T2
Parameter
Thds1_pulse
Tdata_setup
Valid
®
Tadd_setup
IXP46X Product Line of Network Processors—Datasheet
T3
Valid Data
T4
Trecov
T5
Document Number:
T1
Min
11
3
4
4
2
.
Max.
45
17
4
5
5
T2
Valid
Cycles
Cycles
Cycles
Cycles
Cycles
Units
306261-004US
Valid Data
August 2006
T3
1, 5,
5,
2, 4,
3, 5,
4,
Notes
B-01
6
6
6
5
6
Related parts for gwixp465bad
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![AA05B-005L-120D](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet:
![HM3-65787H-5](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet: