maamss0003 Tyco Electronics, maamss0003 Datasheet - Page 2

• Manufacturer Part Number: maamss0003
• Description: Low Noise Catv Amplifier 50 - 1000 Mhz
• Manufacturer: Tyco Electronics

2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
Low Noise CATV Amplifier
50 - 1000 MHz
Test Circuit Schematic
External Circuitry Parts List
Electrical Specifications: T
Test Circuit with M/A-COM Balun ETN1-1-13TR
5. The 1:1 baluns, T1 & T2, are M/A-COM part number ETN1-1-
RF IN
RF IN
Composite Second Order, CSO
Qty
13TR.
Composite Triple Beat, CTB
8
2
2
2
2
T1
T1
Cross modulation
Output VSWR
Gain Flatness
Parameter
Noise Figure
Input VSWR
Output IP3
C1
C1
C2
C2
Balun, 1:1, M/A-COM, ETN1-1-13, SMT (T1,T2)
Capacitor, 2 pF, 0402, SMT, ± 0.25pF (C9-C10)
P1dB
Capacitor, 0.01 uF, 0603, SMT, 10% (C1-C8)
Gain
Inductor, 390 nH, 1008, SMT, 10% (L1, L2)
I
DD
Resistor, 0 ohms, 0603, SMT (R1, R2)
C3
C3
C4
C4
R1
R1
R2
R2
Description
5
Two tones at 397 & 403 MHz, +4 dBm output per tone
135 Channels, +13 dBmV/Channel at the input
135 Channels, +13 dBmV/Channel at the input
135 Channels, +13 dBmV/Channel at the input
C10
C10
A
C9
C9
= 25°C, Freq: 50 - 1000 MHz, V
C8
C8
L2
L2
C5
C5
L1
L1
C7
C7
C6
C6
+5V
+5V
+5V
+5V
Test Conditions
T2
T2
400 MHz
RF
RF
OUT
OUT
+5 Volts
—
—
—
—
—
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macom.com for additional data sheets and product information.
Recommended Test Circuit Layout
6. Reference M/A-COM Application Note S2083 for
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
recommended PCB configuration. R1 and R2 are 0 ohms.
DD
Units
ratio
ratio
dBm
dBm
dBc
dBc
dBc
mA
dB
dB
dB
= +5 Volts, Z
Min.
11.5
160
—
—
—
—
—
—
—
—
—
0
MAAMSS0003
Typ.
1.3:1
1.5:1
= 75 ohms
12.2
190
0.4
3.3
-78
-78
-73
32
24
6
Max.
13.0
225
1.0
-70
-70
-64
4.0
—
—
—
—
V3