sky65105 Skyworks Solutions, Inc., sky65105 Datasheet
![no-image](/images/no-image-200.jpg)
sky65105
Available stocks
Related parts for sky65105
sky65105 Summary of contents
Page 1
... Figure 1 shows a functional block diagram for the SKY65105. The SKY65105 is packaged in a small, 12-pin Multi-Chip Module (MCM) package. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1 ...
Page 2
... GND 11 GND 12 VCC1 Electrical and Mechanical Specifications The absolute maximum ratings of the SKY65105 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Table 4. Typical performance characteristics over temperature of the SKY65105 are illustrated in Figures 3 through 10. GND ...
Page 3
... NF OIP3 Two tones with 100 kHz spacing –1 dBm per IN tone 1960 MHz _ OUT ACPR 2140 MHz _ OUT ACLR PRELIMINARY DATA SHEET • SKY65105 POWER AMPLIFIER Typical Max +85 +125 Typical Max 5 3.6 1900 2200 Min Typical Max 1700 ...
Page 4
... PRELIMINARY DATA SHEET • SKY65105 POWER AMPLIFIER (dBm) IN Figure 3. Typical Over Temperature OUT 1700 1800 1900 Frequency (MHz) Figure 5. Typical Small Signal Gain vs Frequency Over Temperature –40 ...
Page 5
... The following design considerations are general in nature and must be followed regardless of final use or configuration 1. Paths to ground should be made as short as possible. 2. The ground pad of the SKY65105 PA has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the amplifier ...
Page 6
... PRELIMINARY DATA SHEET • SKY65105 POWER AMPLIFIER 4.7 pF Notes: 1) The device ground pad provides both a thermal and electrical ground. This ground path is critical and must be as short as possible. 2) Transmission line lengths T1 and T2 should be minimized. Figure 11. Evaluation Board Schematic, 1700 MHz to 2200 MHz J1 (RF In) Skyworks Solutions, Inc. • ...
Page 7
... Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200085D • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 13, 2007 PRELIMINARY DATA SHEET • SKY65105 POWER AMPLIFIER C1253d ...
Page 8
... Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY65105 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 qC. It can be used for lead or lead-free soldering. For additional information, refer to Skyworks Application Note, PCB Skyworks Solutions, Inc. • ...
Page 9
... Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200085D • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 13, 2007 PRELIMINARY DATA SHEET • SKY65105 POWER AMPLIFIER B ...
Page 10
... Cover tape material: transparent conductive PSA. 3. Cover tape size: 13.3 mm width. 4. All measurements are in millimeters. Figure 16. SKY65105 12-Pin MCM Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 July 13, 2007 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200085D 12.00 ± ...
Page 11
... Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200085D • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 13, 2007 PRELIMINARY DATA SHEET • SKY65105 POWER AMPLIFIER Manufacturing Part Number ...