ftlf1322p1xtr Finisar Corporation., ftlf1322p1xtr Datasheet
ftlf1322p1xtr
Related parts for ftlf1322p1xtr
ftlf1322p1xtr Summary of contents
Page 1
... Industrial operating temperature range: -40°C to 85°C Finisar’s FTLF1322P1xTR Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) They comply with SONET and SDH standards SR/STM I-4. In addition, they comply with SONET and SDH standards at OC-3 IR-1 /STM S-1 ...
Page 2
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 I. Pin Descriptions Pin Symbol 1 V Transmitter Ground (Common with Receiver Ground) EET 2 T Transmitter Fault. Not supported. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. DIS 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. ...
Page 3
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage ...
Page 4
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width Optical Extinction Ratio Optical Rise/Fall Time @ OC-12 Relative Intensity Noise Generated Jitter (peak to peak) Generated Jitter (rms) Mask Margin Receiver Average Rx Sensitivity @ OC-12 ...
Page 5
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125µm SMF @ OC-12 Notes: 1. Compliant with SONET and SDH standards at OC-12 IR-1/STM S-4.1 and OC-12 SR/STM I-4. In addition, they comply with SONET and SDH standards at OC-3 IR-1 /STM S-1.1 and OC-3 SR/STM I-1, as detailed in Finisar Application Note AN-2042 ...
Page 6
... For more information, please see the SFP MSA documentation Note AN-2030. Digital diagnostics for the FTLF1322P1xTR are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. ...
Page 7
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) Finisar Corporation December 2, 2005 Rev.A FTLF1322P1BTR Page 7 ...
Page 8
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 Finisar Corporation December 2, 2005 Rev.A FTLF1322P1WTR Page 8 ...
Page 9
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 X. PCB Layout and Bezel Recommendations Finisar Corporation December 2, 2005 Rev Page 9 ...
Page 10
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 Finisar Corporation December 2, 2005 Rev Page 10 ...
Page 11
... FTLF1322P1xTR Pluggable SFP Product Specification - December 2005 XI. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. Bellcore GR-253 and ITU-T G.957 Specifications. 3. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” ...