92hd81 Integrated Device Technology, 92hd81 Datasheet - Page 20
92hd81
Manufacturer Part Number
92hd81
Description
Single Chip Pc Audio System
Manufacturer
Integrated Device Technology
Datasheet
1.92HD81.pdf
(294 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
92hd81B1B5NLG
Manufacturer:
IDT
Quantity:
150
Company:
Part Number:
92hd81B1C5NLG
Manufacturer:
ST
Quantity:
2 000
Part Number:
92hd81B1C5NLG
Manufacturer:
IDT
Quantity:
20 000
Part Number:
92hd81B1C5NLG XYDX8
Manufacturer:
IDT
Quantity:
20 000
- Current page: 20 of 294
- Download datasheet (4Mb)
SINGLE CHIP PC AUDIO SYSTEM, CODEC+SPEAKER AMPLIFIER+CAPLESS HP+LDO
92HD81
SINGLE CHIP PC AUDIO SYSTEM, CODEC+SPEAKER AMPLIFIER+CAPLESS HP+LDO
2.9.
2.10. Vendor Specific Function Group Power States D4/D5
AFG D3
2.9.1.
Function
Port Presence Detect
state change
GPIO state change
The D3-default state is available for HD Audio compliance. All converters are shut down. Port ampli-
fiers and references are active but in a low power state to prevent pops. Resume times may be
longer than those from D2, but still less than 10mS to meet Intel low power goals. The default power
state for the Audio Function Group after power is applied is D3.
The traditional use for D3 was as a transitional state before power was removed (D3 cold) before the
system entered into standby, hibernate, or shut-down. To conserve power, Intel now promotes using
D3 whenever there are no active streams or other activity that requires the part to consume full
power. The system remains in S0 during this time. When a stream request or user activity requires
the CODEC to become active, the driver will immediately transition the CODEC from D3 to D0. To
enable this use model, the CODEC must resume within 10mS and not pop. Intel HDA ECR-15b /
Low Power White paper power goals are < 30mW when analog PC_Beep is not enabled, and <
60mW when analog PC_Beep is enabled. (Charge pump and BTL amplifier power excluded.)
While in AFG D3, the HD Audio controller may be in a D0 state (HD Audio bus active) or in a D3
state (HD Audio bus held in reset with no Bit_Clk, SData_Out, or Sync activity.) The expected behav-
ior is as follows (see the ECR15b section for more information):
AFG D3cold
The D3cold power state is the lowest power state available that does not use vendor specific verbs.
While in D3cold, the CODEC will still respond to bus requests to revert to a higher power state (dou-
ble AFG reset, link reset). However, audio processing, port presence detect, and other functions are
disabled. Per the HD Audio bus ECR 015b, the D3cold state is intended to be used just prior to
removing power to the CODEC. Typically, power will be removed within 200mS. However, the codec
may exit from the D3cold state by generating 2, back-to-back, AFG reset events. Resume time from
D3cold is less than 200mS.
The 92HD81 introduces vendor specific power states. A vendor defined verb is added to the Audio
Function Group that combines multiple vendor specific power control bits into logical power states
for use by the audio driver. The 2 states defined offer lower power than the 5 existing states defined
in the HD Audio specification and ECR15b. The Vendor Specific D4 state provides lower digital
power consumption relative to D3cold by disabling HD Audio link responses. Vendor specific D5 fur-
1.The Port Presence detect circuit is currently dependent on a clock and
must be changed to generate a wake event.
HDA Bus active
Unsolicited Response
Unsolicited Response
20
HDA Bus stopped
Wake Event
by an unsolicited
response
Wake Event followed by
an unsolicited response
92HD81
1
followed
PC AUDIO
V 0.97 01/09
Related parts for 92hd81
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Integrated Processor
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
Integrated Riscontroller for Low-Cost Systems
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
INTEGRATED RISController FOR LOW-COST SYSTEMS
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
SwitchStar ATM Cell Based 1.2Gbps non-blocking Integrated Switch Controller
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
3.3V CMOS 16-bit bidirectional transceiver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
3.3 CMOS octal buffer/line driver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS octal registered transceivers
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS octal bidirectional transceivers
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS 16-bit buffer/line driver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
2.5 V/3.3 V 10 Bit High Bandwidth Bus Switch with Precharged Outputs
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
High-Speed CMOS Quick Switch 16:8 Multiplexer
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH?? PRODUCTS HIGH-SPEED CMOS QUICKSWITCH DOUBLE-WIDTH BUS SWITCH IDTQS32X245Q2QUICKSWITCH PRODUCTS HIGH-SPEED CMOS QUICKSWITCH DOUBLE-WIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
2.5V / 3.3V 16-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH PRODUCTS 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH PRODUCTS 2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet: