mt88e43 Zarlink Semiconductor, mt88e43 Datasheet - Page 3

• Manufacturer Part Number: mt88e43
• Description: Extended Voltage Calling Number Identification Circuit 2
• Manufacturer: Zarlink Semiconductor

Data Sheet
Pin Description
The MT88E43 provides all the features and
functions offered by Zarlink’s MT8841 (CNIC),
including 1200 baud Bell 202 and CCITT V.23 FSK
demodulation. The 3-wire serial data interface
provided by CNIC has been enhanced to operate in
two modes. In the CNIC compatible mode data
transfer is initiated by the device. A second mode
allows a microcontroller to extract 8-bit data words
from the device. Furthermore, the MT88E43 offers
Idle State Tone Alert Signal and line reversal
detection capability for BT’s CLIP, ring burst
detection for the U.K.’s CCA’s CLIP, and ring and
CAS detection for Bellcore’s CID.
Functional Overview
The MT88E43, Extended Voltage Calling Number
Identification Circuit 2 (ECNIC2) is a device
compatible with BT, the U.K.’s CCA and Bellcore
specifications. As shown in Figure 1, the MT88E43
provides an FSK demodulator as well as a 3-wire
serial interface similar to that of it’s predecessor, the
MT8841 (CNIC). The 3-wire interface has been
enhanced to provide two modes of operation - a
mode whereby data transfer is initiated by the device
and a mode whereby data transfer is initiated by an
external microcontroller.
In addition to supporting all the features and
functions of the MT8841, the MT88E43 also
provides line reversal detection, ring detection and
Pin #
23
24
18
19
20
21
22
Name
St/GT
StD
V
INT
ESt
DR
CD
DD
3-wire Interface: Data Ready (CMOS Output). Active low. In mode 0 this output goes low after
the last DCLK pulse of each data word. This identifies the 8-bit word boundary on the serial
output stream. Typically, DR is used to latch 8-bit words from a serial-to-parallel converter into a
microcontroller. In mode 1 this pin will signal the availability of data.
Carrier Detect (CMOS Output). Active low. A logic low indicates the presence of in-band signal
at the output of the FSK bandpass filter.
Interrupt (Open Drain Output). Active low. It is active when TRIGout or DR is low, or StD is
high. This output stays low until all three signals have become inactive.
Dual Tone Alert Signal Delayed Steering Output (CMOS Output). When high, it indicates
that a guard time qualified alert signal has been detected.
Dual Tone Alert Signal Early Steering Output (CMOS Output). Alert signal detection output.
Used in conjunction with St/GT and external circuitry to implement the detect and non-detect
guard times.
Dual Tone Alert Signal Steering Input/Guard Time (Analog Input/CMOS Output).
voltage greater than V
dual tone has been detected by asserting StD high. A voltage less than V
accept a new dual tone.
Positive Power Supply.
TGt
(see figure 4) at the St/GT pin causes the device to indicate that a
dual tone alert signal/CAS detection. These new
functions eliminate some external circuitry previously
required with the MT8841.
The MT88E43 is compatible with the caller identity
specifications of BT, the U.K.’s CCA, and Bellcore.
BT specifications SIN227 and SIN242 describe the
signalling mechanism between the network and the
Terminal Equipment (TE) for the Caller Display
Service (CDS). CDS provides Calling Line Identity
Presentation (CLIP), which delivers to an on hook
(idle state) TE the identity of an incoming caller
before the first ring.
An incoming CDS call is indicated by a polarity
reversal on the A and B wires (see Figure 3),
followed by an Idle State Tone Alert Signal. Caller ID
FSK information is then transmitted in CCITT V.23
format. MT88E43 can detect the line reversal, tone
alert signal, and demodulate the incoming CCITT
V.23 FSK signals.
The U.K.’s CCA specification TW/P&E/312 proposes
an alternate CDS TE interface. According to TW/
P&E/312, data is transmitted after a single burst of
ringing rather than before the first ringing cycle (as
specified in the BT standards). The Idle State Tone
Alert Signal is not required as it is replaced by a
single ring burst. MT88E43 has the capability to
detect the ring burst. It can also demodulate either
Description
TGt
frees the device to
MT88E43
A
5-55