alm-11136 Avago Technologies, alm-11136 Datasheet
alm-11136
Related parts for alm-11136
alm-11136 Summary of contents
Page 1
... GaAs Enhancement-mode pHEMT process. All matching components are fully integrated within the module and the 50 ohm RF input and output pins are already internally AC-coupled. This makes the ALM-11136 extremely easy to use as the only external parts are DC supply bypass capacitors. For optimum performance ...
Page 2
Absolute Maximum Rating T = 25° Symbol Parameter V Device Voltage output to ground Input Power in,max ( 100 mA Total Power Dissipation diss ...
Page 3
Product Consistency Distribution Charts LSL 80 90 Figure 1. Idd, LSL = nominal = 92 mA, USL = 107 mA 0.7 0.8 Figure 3. NF, nominal = 0.76 dB, USL = 0.91 dB LSL 4 Figure 5. ...
Page 4
... Gnd 5 Gnd 6 Gnd 7 Gnd 8 ALM- Figure 7. Demo Board Layout Diagram – Recommended PCB material is 10 mils Rogers RO4350. – Suggested component values may vary according to layout and PCB material. – Copper trace between the 2 pads is removed before Z2 0(ohm) is placed. 4 Avago Technologies ...
Page 5
Demo Board Schematic C1 C2 1,2,3 4 RFin 50-Ohms TL 5,6,7,8 Module Outline Truth Table Vdd (V) LNA Mode 5 Bypass Mode 0 Fail-safe Mode NC Bypass and Fail-safe mode have similar performance Figure 8. ...
Page 6
Typical Performance RF performance 25° C, Vdd = 5 V for LNA mode, Vdd = 0 V for Bypass mode, measured on demo board in Figure 7. A Signal = CW unless stated otherwise. Application Test Circuit ...
Page 7
Frequency (MHz) Figure 15. IP1dB vs Frequency 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 870 875 880 885 890 895 Frequency ...
Page 8
Typical Scattering Parameters, Vdd = 5 V, Idd = 92 mA LNA SPAR (100 MHz – 20 GHz) Freq S11 S11 (GHz) (dB) (ang) 0.1 -1.42 -140.30 0.5 -2.09 150.05 0.7 -4.34 68.99 0.75 -9.44 44.55 0.77 -12.63 40.36 0.79 ...
Page 9
... Land Pattern 0.845 Pin 1 Combination of Land Pattern and Stencil Opening Part Number Ordering Information Part Number No. of Devices ALM-11136-TR1G 1000 ALM-11136-BLKG 100 9 Pin 1 0.47 Note : 1. Recommended Land Pattern & Stencil Opening. 2. Stencil thickness is 0 mils) 3. All dimension are in MM unless otherwise specified Container 13” ...
Page 10
MCOB Package Dimensions Pin1 Identification 10.00±0.10 Top View 0.845 (pitch) 0.50 0.50 5.20 0.05 8.10 (SM to metal gap) Bottom View Device Orientation REEL USER FEED DIRECTION COVER TAPE 10 7.00±0.10 1.12 Pin 1 0.10 0.845 (pitch) ...
Page 11
Tape Dimensions 12.00 ± 0.10 4.00 ± 0.10 + 0.30 24.00 − 0.10 7.32 ± 0. 2.00 ± 0.10 Ø 1.50 + 0.10 0.318 ± 0.02 8° MAX 2.06 ± 0.10 K. 1.75 ± 0.10 11.50 ± 0.10 ...
Page 12
... BACK VIEW For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. ...