mga-636p8 Avago Technologies, mga-636p8 Datasheet
![no-image](/images/manufacturer_photos/0/0/85/avago_technologies_sml.jpg)
mga-636p8
Related parts for mga-636p8
mga-636p8 Summary of contents
Page 1
... GHz up to 2.5 GHz, MGA-637P8 is recommended. For optimum performance at higher frequency from 2.5 GHz GHz, MGA-638P8 is recommended. All these 3 products, MGA-636P8, MGA-637P8 and MGA-638P8 share the same package and pinout configuration. Pin Configuration and Package Marking 3 2 ...
Page 2
Simplified Schematic L3 [1] [NU] C1 RFin [2] [RFinput] [3] L1 Bias [Vbias2] [4] [NU Note: 1. Device is turned ON when PwrDwn pin is applied with left open. Device is turned ...
Page 3
Electrical Specifications T = 25° C, Vdd = Vbias1 = 4 measurement at 700 MHz, measured on demo board in Figure 5 with component A listed in Table1. Symbol Parameter and Test Condition Idd Drain Current ...
Page 4
... Power Down Mode Figure 6. Demo Board Schematic Diagram Notes: • The schematic is shown with the assumption that similar PCB is used for all MGA-636P8, MGA-637P8 and MGA-638P8. • Detail of the components needed for this product is shown in Table 1. Value 100 pF (Murata (Murata) 4.7 μ ...
Page 5
Typical Performance RF performance 25° C, Vdd = 4.8 V, Idd = 100 mA, measured using 50 ohm input and output board unless stated A otherwise. IIP3 test condition RF1 0.5 0.4 0.3 0.2 0.1 ...
Page 6
Frequency (MHz) Figure 13. Fmin vs Frequency and Idd at 4 500 700 800 900 Frequency (MHz) Figure ...
Page 7
... Below is the table showing the MGA-636P8 Reflection Coefficient Parameters tuned for Maximum IIP3, Vdd = 4.8 V, Idd = 100 mA. Gamma Load position Frequency (GHz) Magnitude 0.50 0.36 0.70 0.36 0.80 0.36 0.90 0.27 1.70 0.27 1.90 0.27 [1] [NU] [2] RFinput [RFinput] Reference Plane [3] Bias [Vbias2] [4] [NU] Figure 16. RFinput and RFoutput Reference Plane Notes: 1. The Maximum IIP3 values are calculated based on Load pull measurements on approximately 100 diff ...
Page 8
Typical Performance RF performance 25° C, Vdd = Vbias1 = 4.8 V, Idd = 108 mA, LNA mode, measured on demo board in Figure 5. Signal unless stated otherwise. Application Test Circuit is shown ...
Page 9
Frequency (GHz) Figure 21. Input Return Loss, Output Return Loss, Gain, Reverse Isolation vs Frequency 120 100 ...
Page 10
Typical Scattering Parameters, Vdd = 4.8 V, Idd = 108 mA LNA SPAR (100 MHz – 20 GHz) Freq S11 S11 (GHz) (dB) (ang) 0.1 -3.611 -62.842 0.5 -10.75 -141.835 0.7 -11.393 -159.056 0.9 -11.693 -171.846 1.0 -12.003 -176.697 1.5 ...
Page 11
... TOP VIEW 0.60±0.05 Exp. DAP 0.35±0.05 0.25±0.05 BOTTOM VIEW 11 Part Number Ordering Information Γ Part Number opt Ang. R MGA-636P8-BLKG n/50 -31.8 0.038 MGA-636P8-TR1G 11.5 0.037 33.2 0.037 54.8 0.038 228 0.043 271 0.043 SIDE VIEW PIN #1 IDENTIFICATION R0.10 1.20±0.05 1.50 Exp. DAP Notes: Ref. 1. All dimensions are in millimeters. ...
Page 12
Recommended PCB Land Pattern and Stencil Design 2.20 1.75 0.00 0.80 0.506x 0.258x 0.458x 0.303x R0.154x PCB Land Pattern 1.75 0.563x 0.506x 0.21 0.172x R0.154x Combines PCB & Stencil Design All Dimension are in millimeters Notes: 1. Stencil thickness is ...
Page 13
Device Orientation REEL USER FEED COVER TAPE DIRECTION Tape Dimensions 10° MAX A O DESCRIPTION CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER PERFORATION DIAMETER PITCH POSITION CARRIER TAPE WIDTH THICKNESS COVER TAPE WIDTH TAPE ...
Page 14
... BACK VIEW For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. ...