adum1230 Analog Devices, Inc., adum1230 Datasheet
adum1230
Available stocks
Related parts for adum1230
adum1230 Summary of contents
Page 1
... V thereby supporting low-side switching to negative voltages. The differential voltage between the high-side and low-side can be as high as 700 result, the ADuM1230 provides reliable control over the switching characteristics of IGBT/MOSFET configurations over a wide range of positive or negative switching voltages. 1 Protected by U ...
Page 2
... ADuM1230 TABLE OF CONTENTS Features .............................................................................................. 1 Applications....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Electrical Characteristics............................................................. 3 Package Characteristics ............................................................... 4 Regulatory Information............................................................... 4 Insulation and Safety-Related Specifications............................ 4 Recommended Operating Conditions ...................................... 4 REVISION HISTORY 12/05—Rev. Sp0 to Rev. A Changes to Figure 1 and Note 1...................................................... 1 Added Typical Application Usage Section .................................... 9 Inserted Figure 14............................................................................. 9 5/05— ...
Page 3
... PHL PLH 100 PWD signal to the 50% level of the falling edge of the V Ix signal to the 50% level of the rising edge of the V Ix Rev Page ADuM1230 ≤ All min/max DDB = 25°C, A Max Unit Test Conditions 4.0 mA 1 200 pF ...
Page 4
... Table Recognized under 1577 component recognition program 1 In accordance with UL1577, each ADuM1230 is proof tested by applying an insulation test voltage ≥ 3000 V rms for 1 second (current leakage detection limit = 5 µA). INSULATION AND SAFETY-RELATED SPECIFICATIONS Table 4. Parameter Rated Dielectric Insulation Voltage Minimum External Air Gap (Clearance) ...
Page 5
... GND A 3 Output differential voltage is defined as GND A 4 Refers to common-mode transients across any insulation barrier. Common- mode transients exceeding the Absolute Maximum Ratings can cause latch permanent damage. Table 7. ADuM1230 Truth Table (Positive Logic Input V State DISABLE IA IB ...
Page 6
... Ground Reference for Output Output Output A Supply Voltage DDA DDA GND 3 14 DD1 A ADuM1230 GND TOP VIEW (Not to Scale) DISABLE DDB GND 8 9 DD1 CONNECT Figure 2 ...
Page 7
... Figure 7. Typical Propagation Delay Variation with Input Supply Voltage 80 100 120 Rev Page ADuM1230 CH. B, FALLING EDGE CH. A, FALLING EDGE CH. A, RISING EDGE CH. B, RISING EDGE 15 OUTPUT SUPPLY VOLTAGE (V) Figure 6. Typical Propagation Delay Variation with Output Supply Voltage (Input Supply Voltage = 5 ...
Page 8
... The transient of the linear component is given by dV /dt = ΔV/Δt CM The ADuM1230’s ability to operate correctly in the presence of linear transients is characterized by the data in Figure 8. The data is based on design simulation and is the maximum linear transient magnitude that the ADuM1230 can tolerate without an operational error. This data shows a higher level of robustness ...
Page 9
... To accommodate these situations, users can choose either a gate driver with a stronger output stage or the buffer configuration with the ADuM1230, as shown in Figure 14. In many cases, the buffer configuration is the less expensive of the two options and provides the greatest amount of design flexibility. The precise buffer/high voltage transistor combination can be selected to fit the application’ ...
Page 10
... ADuM1230 OUTLINE DIMENSIONS 0.30 (0.0118) 0.10 (0.0039) COPLANARITY ORDERING GUIDE No. of Output Peak Model Channels Current (A) 1 ADuM1230BRWZ 2 0.1 ADuM1230BRWZ- 0 Pb-free part. 10.50 (0.4134) 10.10 (0.3976 7.60 (0.2992) 7.40 (0.2913) 10.65 (0.4193 10.00 (0.3937) 1.27 (0.0500) 2.65 (0.1043) BSC 2.35 (0.0925) 0.51 (0.0201) SEATING 0.33 (0.0130) PLANE 0.10 0.31 (0.0122) 0.20 (0.0079) COMPLIANT TO JEDEC STANDARDS MS-013-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS ...
Page 11
... NOTES Rev Page ADuM1230 ...
Page 12
... ADuM1230 NOTES © 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05460-0-12/05(A) T Rev Page ...