sc16461 Silan, sc16461 Datasheet
sc16461
Related parts for sc16461
sc16461 Summary of contents
Page 1
... LED DRIVER IC OF(12~11) x(6~7)SEGMENTS DISPLAY DESCRIPTION SC16461 is an LED controller driven on a 1/7 to 1/8 duty factor. Eleven segment output lines, six grid output lines, 1 segment/grid output lines, one display memory, control circuit, key scan circuit are all incorporated into a single chip to build a highly reliable peripheral device for a single chip microcomputer ...
Page 2
... GR1~GR7 OLGR - TOLSG SG1~SG12 R=51k OSC SC16461 SC16461 = =0V) SS Value -0 -0 +0.5 DD +250 -50 =5V, V =0V amb Min. Typ. Max. 4 -10 -14 -- -20 -25 -- 100 140 -- -- -- 5 0.7V ...
Page 3
... SC16461 provides 2 display mode settings as shown in the diagram below: as stated earlier a command is the first one byte (b0 to b7) transmitted to SC16461 via the DIN pin when STB is “ LOW” . However, for these commands, the bit 3 to bit 6 (b2 to b5) are ignores, bit 7 & bit 8 (b6 to b7) are given a value of “ 0” ...
Page 4
... MSB 0 1 Relevant SC16461 key matrix & key input data storage ram SC16461 key matrix consists array as shown below Each data entered by each key is stored as follows and read by a read command, starting from the last significant bit. When the most significant bit of the data (b0) has been read, the least significant of the next data (b7) is read. K1… ...
Page 5
... When power is turned ON, the address is set at “ 00H” . Please refer to the diagram below. Display mode and RAM address Data transmitted from an external device to SC16461 via the serial interface are stored in the display RAM and are assigned addresses. The RAM addresses of SC16461 are given below in 8 bits unit. SEG1 ...
Page 6
... SERIAL COMMUNICATION FORMAT The following diagram shows the SC16461 serial communication format. RECEPTION (Data/Command Write) STB DIN CLK SWITCHING CHARACTERISTIC WAVEFORM SC16461 switching characteristics waveform is given below. fosc OSC 50% STB CLK DIN Sn Gn Where: PW (clock pulse width) 400ns CLK t (data setup time) ...
Page 7
... Where: Only when "STB" is low , the "CLK" signal is valid. Command 1--Display Mode Setting Command Command 2--Data Setting Command Command 3-- Address Setting Command Data-- Display Data HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn Command2 Command3 Data 1 Command2 Command3 Data Command3 SC16461 Data n Command4 Data REV:1.0 2004.08.03 Page ...
Page 8
... HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn START SET COMMAND 1 SET COMMAND 2 SET COMMAND 3 INITIAL Clear Display RAM SETTING (see Note 4) SET COMMAND 4 Display ON ("10xx1xxx") MAIN PROGRAM SET COMMAND 1 MAIN LOOP SET COMMAND 2 SET COMMAND 3 SET COMMAND 4 Display ON ("10xx1xxx") END SC16461 REV:1.0 2004.08.03 Page ...
Page 9
... APPLICATION CIRCUIT Note: the capacitor (0.1 F) connected between the GND and V the SC16461 chip. SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn pins must be located as near as possible COM / DIGITAL (GRID SC16461 ...
Page 10
... Equipment cases should be earthed. All tools used during assembly, including soldering tools and solder baths, must be earthed. MOS devices should be packed for dispatch in antistatic/conductive containers. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn 20.98±0.10 0.40 19.05 SC16461 UNIT: mm 2.54MAX 0.15±0.05 0.25±0.05 REV:1.0 2004.08.03 Page ...