xr88c92 Exar Corporation, xr88c92 Datasheet - Page 13

• Manufacturer Part Number: xr88c92
• Description: Xr88c92 -dual Uart With 8 Bytes Transmit And Receive Fifo
• Manufacturer: Exar Corporation

Users can program the counter to generate an interrupt
request for this condition on the -INT output by
unmasking the bit-3 in the Interrupt Mask Register (IMR,
address 0x5). After 0x0000 the count becomes
0xFFFF, and the counter continues counting down from
there. If the CPU changes the pre-load value, the
counter will not recognize the new value until it receives
the next start counter command (and is reinitialized).
When a read at the stop counter command register
(address 0xF) is performed, the counter stops the
countdown sequence and clears ISR Bit-3. The count
value should only be read while the counter is stopped
because only one of the count registers (either CUR, at
address 0x6 or CLR, at address 0x7) can be read at a
time. If the counter is running, a decrement of CLR that
requires a borrow from the CUR could take place
between the two register reads. Figure 2 shows the
C/T output in the counter mode. OP3 can be pro-
grammed to show the C/T output.
In addition to the watch dog timer described above, the
C/T can be used for receive timeout function (see
description under CRA, CRB in the registers section
also). The C/T is more accurate and the timeout period
is programmable unlike the watchdog timer. However,
only one channel can use the C/T for receive timeout at
any given time. The C/T timeout mode uses the received
data stream to start the counter. Each time a character
is shifted from the receive shift register to the receive
FIFO, the C/T is reloaded with the programmed value in
CTPU and CTPL and it restarts on the next C/T clock.
Rev. 1.33
C/T OUTPUT IN
COUNTER MODE
TIMER MODE
C/T OUTPUT IN
START C/T COMMAND
Figure 2: C/T output in Timer and Counter modes.
PRELOAD
PRELOAD
VALUE
ISSUED
VALUE
TERMINAL
PRELOAD
TERMINAL
COUNT
VALUE
COUNT
PRELOAD
TERMINAL
VALUE
COUNT
13
TERMINAL
PRELOAD
COUNT
VALUE
If a new character is not received before the C/T reaches
terminal count (= 0x0000), a counter ready interrupt
(ISR bit-3) is generated. The user can appropriately
program the CTPU and CTPL for the desired timeout
period. Typically this is slightly more than one character
time. Note that if C/T is used for receiver timeout, a
counter ready interrupt is generated whereas if the
watchdog timer is used, a receiver ready interrupt is
generated.
TIMER MODE
In the timer mode, the C/T runs continuously once the
start command is issued (by reading the start C/T
command register) and the CPU cannot stop it. When
the stop command is issued (by reading the stop C/T
command register), the CPU only resets the C/T inter-
rupt. This mode allows the C/T to be used as a program-
mable clock source for channels A and B (see CSRA,
CSRB register), and/or a periodic interrupt generator. In
this mode, the C/T generates a square-wave output (see
Figure 2) derived from the programmed timer input
clock source. The square wave generated by the timer
has a period of 2 X (pre-load value) X (period of clock
source) and is available as a clock source for both
channels A and B. Since the timer cannot be stopped,
the values in the registers (CUR:CLR) should not be
read. See description of ACR register to see how to
choose clock source for the C/T.
When the start counter command register (STCR,
PRELOAD
TERMINAL
VALUE
COUNT
TERMINAL
COUNT
PRELOAD
VALUE
XR88C92/192
PRELOAD
TERMINAL
VALUE
COUNT