ad2033 Analog Devices, Inc., ad2033 Datasheet

ad2033

Manufacturer Part Number

ad2033

Description

Truerms /db M.ultirange,~meter.

Manufacturer

Analog Devices, Inc.

Datasheet

1.AD2033.pdf (4 pages)

Current page: 1 of 4
Download datasheet (2Mb)

[

The AD2033 is a 3~ digit, LED display, line-powered digital

The input of the AD203 3 is dc coupled and therefore accepts

GENERAL DESCRIPTION

panel meter (DPM) that measures dc and ac inpu t signals. The

AD2033 measures either the true rms value of ac+dc signals

or the dB value of the ac+dc inpu ts.

to measure an ac signal riding on a constant dc voltage, as in

measuring the ripple of a dc power supply.

ac and/or dc inputs. The input can be ac coupled if it is desired

TRUErmsMEASUREMENTS

rectified average of ac input signals, the AD2033 uses im-

plicit compu ting techniques to derive the actual rms value

not depend on input waveforms. Pulse trains, triangular

pulses and SCR chopped sinewaves, even with high crest

Unlike most ac meters which display rms but measure the

of the ac signals. Thus, the accuracy of the AD2033 does

factors (ratio of peak to rms) and pure sinewaves, are all

measured with high accuracy and no recalibration over a

wide frequency range.

dB MEASUREMENTS

dB measurements

external references (including standard ImW /600S1 used in

audio measurements).

the measurements

from +5mV to +5V. With internal reference, the voltage

can be adjusted via a built-in reference adjust pot. dB

measurements

,Accurate True rms Measurement of Complex ac or ac+dc

True

dB Measurements

tfigh

FEATURES

Bipolar dc Measurements

Full Floating Input Isolation...

Parallel BCD 'Data Outputs

Five Input Ranges

Large 0.5" (13mm) LED Displays

Line Powered

In,dustry Standard Case Design

AfPLlCATIONS

Decibel Oisplay of ac or ac+dc Inputs

For Use in Test Equipment, Power Controllers, Process

Waveforms

Control Equipment and Analytical and Scientific

Instruments

Digits

rlns

Accuracy/wide Frequency Response

a~~~~~

Measurement

can also be made against an arbitrary external

can be made with respect to internal or

are made with regard to a voltage level

In either case, internal or external,

reference, either constant or slow varying. The external

reference is applied to a pin on the top rear connector,

may be divided down from a higher reference voltage.

FIVE INPUT RANGES

The AD2033 provides five separate inputs: 199.9mV;

When reading is dB, these input ranges are extended to

greatly increases reliability.

ranges, but the standardunit

The use of MOS/LSI (Metal Oxide Semiconductor/Large

the number of components,

500mV, 5V, SOY, SOOV and 62SV rms.

Factory calibration provides excellent accuracies on all five

rms FS range. Optimized calibration for the other ranges

SECOND GENERATION

Scale Integration)

1.999V; 19.99V; 199.9V and 600V rms Full Scale (FS).

1000V rms FS input is available upon special request.

is also available. The floating opto-isolated

withstands common mode voltages up to 300V rms, even

with digital outputs and control lines connected.

only facilitates making measurements

environments,

ments which are rarely referenced directly to ground.

but is essential in making current measure-

integrated circuits in the AD2033 reduces

M.ultirange,~Meter.

DPM DESIGN

.'AD2033

cuts power consumption

is optimized for the 1.999V

Truerms

in various electrical

analog input

-~--

This not

and

, I

Related parts for ad2033

ad2033 Summary of contents

Page 1

... AD2033 uses im- plicit compu ting techniques to derive the actual rms value of the ac signals. Thus, the accuracy of the AD2033 does not depend on input waveforms. Pulse trains, triangular pulses and SCR chopped sinewaves, even with high crest ...

Page 2

... AD2033 Converter arc needed 30 pin, 0.156" spacing card cdge connector, Optional illumi- . AD2033 rms/dB Card Connector must sink 25mA 36 pin, 0.156" spacing card edge connecror, Optional: 'Overrange of 250% of full scale is available for analog only output data; LogIc "I" or open (pin R) on all ranges except ...

Page 3

... RDG :1:0.3% RDG :1:0.05% FS .:1:0.05% FS :1:1digit :1:1digit :to. :l:60jJ.V/C :t75ppm/C :t75ppm/C 30Hz to 10kHz 30Hz to 10kHz 30Hz to 100kHz 30Hz to 100kHz Table 1. AD2033 rms Specifications FEEDBACK RANGE SELECT ICI FEEDBACK 0 {DIFEEDBACK J 0 IAI 12 RANGES MB FEEDBACK ' l EI RANGE C '-~ of bias current 0 INPUT RANGE A (~IINPUT RANGES B,C,D ...

Page 4

... Set up in similar fashion on other ranges. Bipolar dc Measurements By bypassing the nos/dB front end possible to use the AD2033 to measure and display a bipolar dc value on the 1.999V FS. The input pin for this measurement the AID Input Pin (Pin 18 of P2). Connect low side to Ground (Pins 1-6). A shunt capacitor (0.047/-LF) at the AID Input is needed to limit input impedance ...

Related keywords

ad2033 datasheet
ad2033 data sheet
ad2033 pdf datasheet
ad2033 component
ad2033 part
ad2033 distributor
ad2033 RoHS
ad2033 datasheet download