op4013b RF Monolithics, Inc., op4013b Datasheet
![no-image](/images/no-image-200.jpg)
op4013b
Manufacturer Part Number
op4013b
Description
693.48342mhz Optical Timing Clock
Manufacturer
RF Monolithics, Inc.
Datasheet
1.OP4013B.pdf
(2 pages)
Electrical Characteristics
1.
2.
3.
4.
5.
6.
7.
8.
9.
www.RFM.com
©2008 by RF Monolithics, Inc.
• Quartz SAW Stabilized and Filtered “Diff Sine” Technology
• Fundamental-Mode Oscillation at 693.48342 MHz
• Voltage Tunable for Phase Lock Loop Operations
• Optical Timing Reference for 10G Eithernet Applications
The output of this device is generated and filtered by narrowband quartz SAW elements at 693.48 MHz. The
configuration of this clock is intended to provide a pure signal for optical timing applications in noisy signal
environments. The Q/Qbar differential output swing of ±1 volt about 0 vdc has symmetry better than ±1% into
loads from 40 ohms to 70 ohms; determined by customer application. The long term frequency accuracy is
set by an external reference source allowing this device to complete a Phase Lock Loop design without the
usual noise and jitter problems associated with PLL’s.
Absolute Maximum Ratings
Rating
DC Suppy Voltage
Tune Voltage
Case Temperature
Output DC Resistance (between Q & Q)
DC Power Supply
Operating Frequency
Q and Q Output
Phase Noise
Q and Q Jitter
Operating Case Temperature
Lid Symbolization (YY=Year, WW=Week)
Unless otherwise noted, all specifications include any combination of load VSWR, VCC, and TC. In addition, Q and Q are terminated into 50 Ω loads
to ground. (See: Typical Test Circuit.)
Customer useful tune range in excess of what part requires over temp, aging, pushing, pulling & accuracy.
The design, manufacturing process, and specifications of this device are subject to change without notice.
Only under the nominal conditions of 50 Ω load impedance with VSWR ≤ 1.2 and nominal power supply voltage.
Symmetry is defined as the pulse width (in percent of total period) measured at the 50% points of Q or Q. (See: Timing Definitions.)
Jitter and other spurious outputs induced by externally generated electrical noise on V
specification, except where noted. External voltage regulation and careful PCB layout are recommended for optimum performance.
Applies to period jitter of Q and Q. Measurements are made with the Tektronix CSA803 signal analyzer with at least 1000 samples.
Linearity is a function of the percentage variation from a permitted linear deviation versus the amount of frequency tune range. See Linearity
Definition.
One or more of the following United States patents apply: 4,616,197; 4,670,681; 4,760,352.
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device.
Notes:
E-mail: info@rfm.com
Characteristic
Voltage into 50 Ω (VSWR≤1.2)
Absolute Frequency
Tune Range
Tune Voltage
Tuning Linearity
Modulation Bandwidth
Operating Load VSWR
Symmetry
Harmonic Spurious
Nonharmonic Spurious
dBc/Hz@100Hz offset
RMS Jitter
No Noise on V
200 mV
Operating Voltage
Operating Current
P-P
1kHz offset
10k offset
Noise Floor
from 1MHz to ½ f
CC
O
on
Sym
V
I
V
T
f
CC
CC
O
C
O
Value
-55 to 100
0 to 5.5
3, 4, 6, 7
3, 4, 6, 7
3, 4, 6, 7
0 to 6
Notes
3, 4, 5
3, 4, 6
1, 9
1, 8
1, 3
1, 3
1, 3
1, 3
1,3
1,3
2
1
3
CC
Units
RFM OP4013B YYWW
Minimum
or mechanical vibration are not included in this
-10°C
0.60
3.13
125
49
50
VDC
VDC
0
°C
693.483
Typical
3.3, 5.0
±100
-100
-125
-150
±5%
265
-70
12
12
2
693.48342 MHz
Timing Clock
OP4013B
Optical
Maximum
+80°C
SMC-08
5.25
1.1
2:1
-30
-60
+3
51
70
OP4013B - 3/27/08
dBc/Hz
dBc/Hz
PS
PS
PS
Units
MHz
VDC
VDC
ppm
V
kHz
dBc
dBc
Page 1 of 2
KΩ
mA
°C
%
P-P
P-P
P-P
P-P
Related parts for op4013b
op4013b Summary of contents
Page 1
... RFM OP4013B YYWW or mechanical vibration are not included in this CC Units MHz ppm VDC kHz V P-P % dBc dBc dBc/Hz dBc/Hz PS P-P PS P-P PS P-P KΩ VDC mA °C Page OP4013B - 3/27/08 ...
Page 2
... Nominal 0.141 Nominal E 2.24 Nominal 0.088 Nominal F 1.27 Nominal 0.050 Nominal G 2.54 Nominal 0.100 Nominal H 3.05 Nominal 0.120 Nominal J 1.93 Nominal 0.076 Nominal K 5.54 Nominal 0.218 Nominal L 4.32 Nominal 0.170 Nominal M 4.83 Nominal 0.190 Nominal N 0.50 Nominal 0.020 Nominal D E (X8 (X3) (X2 MAX 0.550 0.380 Page OP4013B - 3/27/08 ...