cop888eb National Semiconductor Corporation, cop888eb Datasheet - Page 36
![no-image](/images/no-image-200.jpg)
cop888eb
Manufacturer Part Number
cop888eb
Description
8-bit Cmos Rom Based Microcontrollers With 8k Memory, Can Interface, 8-bit A/d, And Usart
Manufacturer
National Semiconductor Corporation
Datasheet
1.COP888EB.pdf
(75 pages)
- Current page: 36 of 75
- Download datasheet (818Kb)
www.national.com
Frame Formats
SYNCHRONIZATION
Every receiver starts with a “hard synchronization” on the
falling edge of the SOF bit. One bit time consists of four bit
segments: Synchronization segment, propagation segment,
phase segment 1 and phase segment 2.
A falling edge of the data signal should be in the synchroni-
zation segment. This segment has the fixed length of one
time quanta. To compensate for the various delays within a
network, the propagation segment is used. Its length is pro-
grammable from 1 to 8 time quanta. Phase segment 1 and
phase segment 2 are used to resynchronize during an active
frame. The length of these segments is from 1 to 8 time
quanta long.
A) Synchronization segment
B) Propagation segment
FIGURE 27. CAN Bus States
(Continued)
FIGURE 28. Bit Timing
DS012837-32
36
Two types of synchronization are supported:
Hard synchronization is done with the falling edge on the
bus while the bus is idle, which is then interpreted as the
SOF. It restarts the internal logic.
Soft synchronization is used to lengthen or shorten the bit
time while a data or remote frame is received. Whenever a
falling edge is detected in the propagation segment or in
phase segment 1, the segment is lengthened by a specific
value, the resynchronization jump width (see Figure 29 ).
If a falling edge lies in the phase segment 2 (as shown in Fig-
ure 29 ) it is shortened by the resynchronization jump width.
Only one resynchronization is allowed during one bit time.
The sample point lies between the two phase segments and
is the point where the received data is supposed to be valid.
The transmission point lies at the end of phase segment 2 to
start a new bit time with the synchronization segment.
1. The resynchronization jump width (RJW) is automati-
2. (PS1 — BTL settings any PSC setting) The PS1 of the
cally determined from the programmed value of PS. If a
soft resynchronization is done during phase segment 1
or the propagation segment, then RJW will either be
equal to 4 internal CAN clocks (CKI/(1 + divider) ) or the
programmed value of PS, whichever is less. PS2 will
never be shorter than 1 internal CAN clock.
BTL should always be programmed to values greater
than 1. To allow device resynchronization for positive
and negative phase errors on the bus. (if PS1 is pro-
grammed to one, a bit time could only be lengthened
and never shortened which basically disables half of the
synchronization).
DS012837-33
Related parts for cop888eb
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![mma1270keg](/images/no-image3.png)
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC12034](/images/no-image3.png)
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2350](/images/no-image3.png)
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2324](/images/no-image3.png)
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2301](/images/no-image3.png)
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![NDS8963](/images/no-image3.png)
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM1201](/images/no-image3.png)
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM3501TL-16](/images/no-image3.png)
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![AD9621](/images/no-image3.png)
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM2403](/images/no-image3.png)
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM592M](/images/no-image3.png)
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC10061](/images/no-image3.png)
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS36277TMX](/images/no-image3.png)
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS3654](/images/no-image3.png)
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS3662](/images/no-image3.png)
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: