mn101cf77g Panasonic Corporation of North America, mn101cf77g Datasheet

no-image

mn101cf77g

Manufacturer Part Number
mn101cf77g
Description
Mn101c77a
Manufacturer
Panasonic Corporation of North America
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mn101cf77gXA
Quantity:
96
Part Number:
mn101cf77gXN
Manufacturer:
STM
Quantity:
1 925
Part Number:
mn101cf77gXN
Manufacturer:
Panasonic Electronic Components - Semiconductor Products
Quantity:
10 000
 Interrupts
 Timer Counter
 Serial interface
 DMA controller
 I/O Pins
 A/D converter
 D/A converter
 Special Ports
 ROM Correction
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
RESET. Watchdog. External 0 to 4. Timer 0. Timer 1. Timer 4 to 6. Timer 7 (2 systems). Time base. Serial 0 reception. Serial 0
transmission. Serial 1 reception. Serial 1 transmission. Serial 3. Serial 4. Automatic transfer finish. A/D conversion finish. Key interrupts (8
lines)
8-bit timer × 5
16-bit timer × 1
Time base timer: One-minute count setting
Watchdog timer × 1
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type/Single-master I
I
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer
I/O
10-bit × 7 channels (with S/H)
8-bit × 2 channels (Serves as AD pin, as well)
Buzzer output. Remote control carrier output. High-current drive port
Correcting address designation: Up to 3 addresses possible
2
C slave × 1: Serial 4
MN101C77 Series
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 1 baud rate timer
Timer 5 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
Serial 4 ...................I
53 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
width measurement. Input capture
2
C high-speed transfer mode. 7-bit/10-bit address setting. General call
LQFP064-P-1414
MN101C77A
1.5K
32K
2
C × 1: Serial 3
*: The operation guarantee range for flash memory built-in type is 2.7 V to 3.6 V.
TQFP064-P-1010C
LQFP064-P-1414,
MN101C77C
48K
3K
0.119 µs (at 2.5 V to 3.6 V, 8.39 MHz)*
62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
0.1 µs (at 2.5 V to 3.6 V, 20 MHz)*
0.2 µs (at 2.1 V to 3.6 V, 10 MHz)*
Mask ROM
0.5 µs (at 1.8 V to 3.6 V, 4 MHz)*
[Double speed]
MN101C77D
[Standard]
64K
LQFP064-P-1414
MN101C77F
96K
6K
TQFP064-P-1010C
LQFP064-P-1414,
MN101CF77G
MAD00038LEM
FLASH
128K

Related parts for mn101cf77g

mn101cf77g Summary of contents

Page 1

... MHz)* 0.5 µs ( MHz)* 62.5 µs ( kHz)* [Double speed] 0.119 µs (at 2 3.6 V, 8.39 MHz)* *: The operation guarantee range for flash memory built-in type is 2 3.6 V. MN101C77F MN101CF77G 96K 6K LQFP064-P-1414, LQFP064-P-1414 TQFP064-P-1010C MAD00038LEM FLASH ...

Page 2

... P81, LED1 P80, LED0 AVSS PA0, AN0, DA0 PA1, AN1, DA1 PA2, AN2 Note) Pin 5 serves as the VPP pin in the MN101CF77G, and cannot be used as a user pin. MAD00038LEM Condition fosc = 20 MHz (fs = fosc/2). VDD = 3.3 V fosc = 8.39 MHz (fs = fosc/2). VDD = 3 32.768 kHz (fs = fx/2). VDD = 3 32.768 kHz. VDD = 3 ° ...

Page 3

Request for your special attention and precautions in using the technical information and (1) If any of the products or technical information described in this book exported or provided to non-residents, the laws and regulations of the ...

Related keywords