tps4100a Tripath Technology Inc., tps4100a Datasheet
tps4100a
Related parts for tps4100a
tps4100a Summary of contents
Page 1
... The TPS4100A channel bridged (16 power transistors) output power stage. The TPS4100A accepts 5V CMOS logic signals from a Class-T processor, such as TCD6001, to create a high fidelity 4-channel audio amplifier ...
Page 2
... Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. See the table below for Operating Conditions. Note 2: Supply voltage is limited in AM Mode due to additional power dissipation of output stage when operating in Class B mode. Please note that the TPS4100A is still fully protected from load dump transients in AM Mode. : The in Note 3 put section pins (pins 1-9, 11,12) should not be connected to voltages over 5 ...
Page 3
... I Over-current detect OCD Pout Output Power (Note 7) Note 9: The TPS4100A heat sinking in AM Mode must be increased (as compared to Class-T mode) to sustain the typical output numbers. This is due to the lower efficiency of Class B output stage operation. 3 Tripath Technology, Inc. – Technical Information Conditions MIN. ...
Page 4
... Over-Current Detect OC VP Load Dump Voltage Withstand MAX TPS4100A Pinout 32-pin SSIP Package Note: The heat slug of the TPS4100A is connected to PGND. 4 Tripath Technology, Inc. – Technical Information CONDITIONS Over-voltage turn on (amp muted) Over-voltage turn off (mute off) Under-voltage turn off (mute off) ...
Page 5
... TPS4100A Pinout PIN NAME/FUNCTION TYPE 1 SLEEPB INPUT (L) Logic input, ACTIVE LOW. Setting SLEEP to low puts the TPS4100A in sleep Y1, Y2, Y3, Y4 INPUT (L) Non-inverted switching modulator inputs Y1B, Y2B, Y3B, Y4B INPUT (L) Inverted switching modulator inputs. 10 MUTEB INPUT (L) Logic Input, ACTIVE LOW. Setting MUTE to low puts the device in mute mode. ...
Page 6
... CPUMP Cbr Cbr 390uF 0.1uF Dcp Dcp Ccp close to 0.1uF PIN28 VPP VPP 10uH 0.47uF 10; 0.47uF 0.22uF Lo 10uH RL Co 0.47uF Rz 10; 0.47uF 0.22uF Lo 10uH RL Co 0.47uF Rz 10; 0.47uF 0.22uF Lo 10uH 0.47uF 10; 0.47uF 0.22uF TPS4100A – KL/Rev. 1.1/11.05 ...
Page 7
... Components Description C Supply decoupling for the power supply pins. For optimum performance, these S components should be located close to the TPS4100A and returned to their respective “ground” as shown in the Application/Test Circuit. C Supply decoupling for the high current full-bridge supply pins. These components BR must be located as close to the power supply pins as possible to minimize output ringing which causes power supply overshoot ...
Page 8
... Total output Power E fficienc y Power Dissipation V = 25V PP Ω 1kH 22H z - 20kH z(AES17) 100 150 200 250 300 350 400 Total Output Power (W ) TPS4100A – KL/Rev. 1.1/11. 25V PP 100 200 10 500 ...
Page 9
... E fficiency and P ower D issipation versus Total output P ower P ower Diss ipation E ffic ienc y AM MOD 4.4V PP Ω z(AES1 Total Output P ower (W ) TPS4100A – KL/Rev. 1.1/11. 100 ...
Page 10
... The TPS4100A is typically configured as a high power, high efficiency, four channel switching amplifier. The TPS4100A also has an additional amplifier mode named “AM Mode.” By pulling the AM pin to a logic high level, the TPS4100A is configured as a Class B amplifier as opposed to the normal, Class-T amplifier ...
Page 11
... This fault puts the amplifier into mute and resets automatically once the supply voltage is reduced below the hysteresis band. The TPS4100A also has built-in load dump protection. This circuit puts the amplifier into sleep mode if the supply voltage is increased above 30V. The TPS4100A is able to survive power supply spikes to 60V if the duration is less than 50mS. ...
Page 12
... The SLEEPB (SLEEP) pin is a logic input that when pulled low puts the TPS4100A into a low quiescent current mode. This pin must be pulled external 3. supply to activate (disable sleep mode) the TPS4100A. The sleep pin cannot be pulled up to VPP due to internal circuitry limitations. The amplifier takes approximately 500mS to come out of sleep ...
Page 13
... MOSFETs and/or other components. The RC dampens the peaking and prevents problems highly recommended that the design process for a TPS4100A amplifier include an analysis of the interaction of intended speaker(s) with the LC filter and RC damper to ensure the desired frequency response is attained ...
Page 14
... Package Information 14 Tripath Technology, Inc. – Technical Information TPS4100A – KL/Rev. 1.1/11.05 ...
Page 15
... 2560 Orchard Parkway, San Jose, CA 95131 408.750.3000 - P 408.750.3001 - F For more Sales Information, please visit us @ For more Technical Information, please visit Tripath Technology, Inc. – Technical Information www.tripath.com/cont_s.htm www.tripath.com/data.htm TPS4100A – KL/Rev. 1.1/11.05 ...