zxbm1016 Zetex Semiconductors plc., zxbm1016 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
zxbm1016
Manufacturer Part Number
zxbm1016
Description
High Efficiency Variable Speed Single-phase Fan Motor Controller
Manufacturer
Zetex Semiconductors plc.
Datasheet
1.ZXBM1016.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ZXBM1016
Manufacturer:
ZETEX
Quantity:
20 000
Company:
Part Number:
zxbm1016ST20TA
Manufacturer:
TI
Quantity:
500
Part Number:
zxbm1016ST20TA
Manufacturer:
DIODES/ZETEX
Quantity:
20 000
Company:
Part Number:
zxbm1016ST20TC
Manufacturer:
Diodes/Zetex
Quantity:
17 500
Part Number:
zxbm1016ST20TC
Manufacturer:
DIODES/ZETEX
Quantity:
20 000
C
A capacitor is connected from this pin to ground. It is used to store a signal that is proportional
to the commutation period. The stored signal is a representation of the motor speed and is used
by the tail-end control circuitry. It will normally be the same value as that applied to the C
Range - Speed range setting pin
The ZXBM1016 is designed to operate over a predefined dynamic range. This will normally be in
excess of 10:1 i.e. the lowest speed will be 1/10 of the full speed. In some instance the speed range
might be 200rpm to 2,000rpm yet in others it could be 1,000 to 10,000rpm. This pin allows the tail-
end current control operation to be tuned to the desired speed range. To do this a resistor is
attached between the range pin and the ThRef pin.
The following graph gives a range of resistor values against the speed range.
Typically a 220k
however a lower value can be used to enable the motor to be run at higher speeds. Conversely a
higher value will be needed for motors running at a lower speed range.
CPWM - Sets PWM frequency
This pin has an external capacitor attached to set the PWM frequency for the phase drive outputs.
A capacitor value of 0.1nF will provide a PWM frequency of typically 25kHz.
FG - Frequency generator (speed)
This is the frequency generator output and is a buffered signal from the Hall sensor.
This is an open collector drive giving an active pull down with the high level being provided by
an external pull up resistor.
Ph1Lo and Ph2Lo - Low-side external H-bridge driver
These pair of outputs drive the low side of the external power device H-bridge that in turn drives
the single phase winding. These outputs provide both the commutation and PWM waveforms.
The outputs are active pull-up and active pull-down to help faster switching off when driving
MOSFET devices with a high gate capacitance. When in the high state the outputs will provide up
to 80mA of drive into the base or gates of external transistors as shown in the typical application
circuit shown on the front page.
When in the low state the active phase drive is again capable of sinking up to 80mA to aid turn
off times during PWM operation. When the phase is inactive the output is held low by a 7.5k
internal pull-down resistor.
Issue 1 - February 2007
© Zetex Semiconductors plc 2007
INT
- Integrator timing capacitor
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
Speed vs C
0
750kΩ
2000
R
120kΩ
360kΩ
220kΩ
470kΩ
Range
Speed (rpm)
resistor will cover most mid speed range motors of 600rpm to 6,000rpm,
4000
LCK
peak voltage
6000
C
LCK
8000
= 0.47μF
10000
8
ZXBM1016
www.zetex.com
LCK
pin.