lx1665 Microsemi Corporation, lx1665 Datasheet - Page 8

• Manufacturer Part Number: lx1665
• Description: Dual Output Pwm Controllers With 5-bit Dac
• Manufacturer: Microsemi Corporation

LX1664/64A, LX1665/65A
8
IC OPERATION
Referring to the block diagram and typical application circuit, the
output turns ON the top MOSFET, allowing the inductor current to
increase. At the error comparator threshold, the PWM latch is reset,
the top MOSFET turns OFF and the synchronous MOSFET turns ON.
The OFF-time capacitor C
valley voltage, the synchronous MOSFET turns OFF and the top
MOSFET turns on. A special break-before-make circuit prevents
simultaneous conduction of the two MOSFETS.
response. The INV pin is connected to the positive side of the
current sense resistor, so the controller regulates the positive side
of the sense resistor. At light loads, the output voltage will be
regulated above the nominal setpoint voltage. At heavy loads, the
output voltage will drop below the nominal setpoint voltage. To
minimize frequency variation with varying output voltage, the OFF-
time is modulated as a function of the voltage at the V
ERROR VOLTAGE COMPARATOR
The error voltage comparator compares the voltage at the positive
side of the sense resistor to the set voltage plus 40mV. An external
filter is recommended for high-frequency noise.
CURRENT LIMIT
Current limiting is done by sensing the inductor current. Exceeding
the current sense threshold turns the output drive OFF and latches
it OFF until the PWM latch Set input goes high again. See Current
Limit Section in "Using The LX1664/65 Devices" later in this data
sheet.
OFF-TIME CONTROL TIMING
The timing capacitor C
timing capacitor is quickly charged during the ON time of the top
MOSFET and allowed to discharge when the top MOSFET is OFF.
In order to minimize frequency variations while providing different
supply voltages, the discharge current is modulated by the voltage
at the V
V
UNDER VOLTAGE LOCKOUT
The purpose of the UVLO is to keep the output drive off until the
input voltage reaches the start-up threshold. At voltages below the
start-up voltage, the UVLO comparator disables the internal biasing,
and turns off the output drives. The SS (Soft-Start) pin is pulled low.
SYNCHRONOUS CONTROL
The synchronous control section incorporates a unique break-
before-make function to ensure that the primary switch and the
synchronous switch are not turned on at the same time. Approxi-
mately 100 nanoseconds of deadtime is provided by the break-
before-make circuitry to protect the MOSFET switches.
CC_CORE
The V
CC_CORE
voltage.
CC_CORE
pin. The OFF-time is inversely proportional to the
pin is offset by +40mV to enhance transient
T
allows programming of the OFF-time. The
T
is now allowed to discharge. At the
P R O D U C T D A T A B O O K 1 9 9 6 / 1 9 9 7
D
UAL
O
P
UTPUT
R O D U C T I O N
T H E O R Y O F O P E R A T I O N
PWM C
CC_CORE
pin.
ONTROLLERS WITH
D
PROGRAMMING THE OUTPUT VOLTAGE
The output voltage is set by means of a 5-bit digital Voltage
Identification (VID) word (See Table 1). The VID code may be hard-
wired into the package of the processor which do not have a VID
code, the output voltage can be set by means of a DIP switch or
jumpers. For a low or '0' signal, connect the VID pin to ground (DIP
switch ON); for a high or '1' signal, leave the VID pin open (DIP
switch OFF).
directly with a Pentium Pro or Pentium II processor. Therefore, all
inputs are expected to be either ground or floating. Any floating
input will be pulled high by internal connections. If using a Socket
7 processor, or other load, the VID code can be set directly by
connecting jumpers or DIP switches to the VID[0:4] pins.
should not be connected high. Unpredictable output voltages
may result. If the LX166x devices are to be connected to a logic
circuit, such as BIOS, for programming of output voltage, they
should be buffered using a CMOS gate with open-drain, such as a
74HC125 or 74C906.
POWER GOOD SIGNAL (LX1665 only)
An open collector output is provided which presents high imped-
ance when the output voltage is between 90% and 117% of the
programmed VID voltage, measured at the SS pin. Outside this
window the output presents a low impedance path to ground. The
Power Good function also toggles low during OVP operation.
OVER-VOLTAGE PROTECTION
The controller is inherently protected from an over-voltage condi-
tion due to its constant OFF-time architecture. However, should a
failure occur at the power switch, an over-voltage drive pin is
provided (on the LX1665 only) which can drive an external SCR
crowbar (Q
removed and power recycled for the LX1665 to resume normal
operation (See Figure 9).
LINEAR REGULATOR
The product highlight application shows an application schematic
using a MOSFET as the pass element for a linear regulator. this
output is suitable for converting the 5V system supply to 3.3V for
processor I/O buffers, memory, chipset and other components. The
output can be adjusted to any voltage between 1.5V and 3.6V in
order to supply other (lower) power requirements on a mother-
board. See section "Using the LX1664/1665 Devices" at the end of
this data sheet.
A T A
The five VID pins on the LX166x series are designed to interface
The VID pins are not designed to take TTL inputs, and
S
3
), and so blow a fuse (F
H E E T
5-B
IT
DAC
1
). the fault condition must be