lnk520 Power Integrations, Inc., lnk520 Datasheet - Page 9
![no-image](/images/no-image-200.jpg)
lnk520
Manufacturer Part Number
lnk520
Description
Energy Ef?cient, Cv Or Cv/cc Switcher For Very Low Cost Adapters And Chargers
Manufacturer
Power Integrations, Inc.
Datasheet
1.LNK520.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lnk520GN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
lnk520GN
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
lnk520GN-TL
Manufacturer:
ST
Quantity:
245
Company:
Part Number:
lnk520GN-TL
Manufacturer:
PowerInt
Quantity:
3 000
Part Number:
lnk520GN-TL
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
lnk520PN
Manufacturer:
POWER
Quantity:
15 000
Part Number:
lnk520PN
Manufacturer:
POWER
Quantity:
20 000
Core gaps should be uniform. Uneven core gapping, especially
with small gap sizes, may cause variation in the primary
inductance with flux density (partial saturation) and make the
constant current region non-linear. To verify uniform gapping,
it is recommended that the primary current wave-shape be
examined while feeding the supply from a DC source. The
gradient is defined as di/dt = V/L and should remain constant
throughout the MOSFET on time. Any change in gradient of
the current ramp is an indication of uneven gapping.
Measurements made using a LCR bridge should not be solely
relied upon; typically these instruments only measure at currents
of a few milliamps. This is insufficient to generate high enough
flux densities in the core to show uneven gapping.
For a typical EE16 or EE13 core using center leg gapping, a
0.08 mm gap allows a primary inductance tolerance of ±10% to
be maintained in standard high volume production. This allows
the EE13 to be used in designs up to 2.75 W with less than
300 mW no-load consumption. Using outer leg film gapping
reduces inductance tolerance to ±7% or better, allowing designs
up to 3 W. Using the larger EE16 allows for a 3 W output
with center leg gapping. The EE13 core size may be attractive
in designs were space is limited or if there is a cost advantage
over the EE16.
The transformer turns ratio should be selected to give a V
(output voltage reflected through secondary to primary turns
ratio) of 40 V to 80 V. Higher V
capability of LinkSwitch but also increases no-load power
consumption. This allows even higher values to be used in
designs where no-load power is not a concern. However care
should be taken to ensure that the maximum temperature rise
of the device is acceptable at the upper limit of the output
characteristic when used in a charger application. In all cases,
discontinuous mode operation should be maintained and note
that the linearity of the CC region of the power supply output
characteristic is influenced by the bias voltage. If this is an
important aspect of the application, the output characteristic
should be checked before finalizing the design.
Output Characteristic Variation
Both the device tolerance and external circuit govern the overall
tolerance of the LinkSwitch power supply output characteristic.
Estimated peak power point tolerances for a LNK520, 2.75 W
design are ±10% for voltage and ±24% for current limit for
overall variation in high volume manufacturing. This includes
device and transformer tolerances (±7.5% assumed) and line
variation. Lower power designs may have poorer constant
current linearity.
As the output load reduces from the peak power point, the
output voltage will tend to rise due to tracking errors compared
to the load terminals. Sources of these errors include the
output cable drop, output diode forward voltage and leakage
OR
increases the output power
OR
inductance, which is the dominant cause. As the load reduces,
the primary operating peak current reduces, together with the
leakage inductance energy, which reduces the peak charging
of the clamp capacitor.
At very light or no-load, typically less than 2 mA of output current,
the output voltage rises due to leakage inductance peak charging
of the secondary. This voltage rise can be reduced with a small
preload with little change to no-load power consumption. The
output voltage load variation can be improved across the whole
load range by adding an optocoupler and secondary reference
(Figure 6). The secondary reference is designed to only provide
feedback above the normal peak power point voltage to maintain
the correct constant current characteristic.
Component Selection
The schematic shown in Figure 10 outlines the key components
needed for a LinkSwitch supply.
Clamp diode – D5
Diode D5 can be an ultra-fast (t
or standard recovery diode with a voltage rating of 600 V or
higher. A standard recovery diode is recommended as it improves
the CV characteristic, but should be a glass-passivated type
(1N400xGP) to ensure a defined reverse recovery time.
Clamp Capacitor – C4
Capacitor C4 should be in the range of 100 pF to 1000 pF,
500 V capacitor. A low cost ceramic disc is recommended.
The tolerance of this part has a very minor effect on the output
characteristic so any of the standard ±5%, ±10% or ±20%
tolerances are acceptable. 330 pF is a good initial value, iterated
with R1.
Clamp Resistor – R1
The value of R1 is selected to be the highest value that still
provides adequate margin to the DRAIN BV
line. As a general rule, the value of C4 should be minimized
and R1 maximized.
CONTROL Pin Capacitor – C5
Capacitor C5 is used during start-up to power LinkSwitch and
sets the auto-restart frequency. For designs that have a battery
load, this component should have a value of 0.22 µF and for
resistive loads a value of 1 µF. This ensures there is sufficient
time during start-up for the output voltage to reach regulation.
Any capacitor type is acceptable with a voltage rating of
10 V or above.
Bias Capacitor – C3
Capacitor C3 should be a 1 µF, 50 V electrolytic type. The
voltage rating is consistent with the 20 V to 30 V seen across
the bias winding. Lower values give poorer regulation.
rr
< 50 ns), a fast (t
LNK520
DSS
rating at high
rr
2/05
< 250 ns)
E
9