mxd1013 Maxim Integrated Products, Inc., mxd1013 Datasheet - Page 2

• Manufacturer Part Number: mxd1013
• Description: Mxd1013 3-in-1 Silicon Delay Line
• Manufacturer: Maxim Integrated Products, Inc.

ABSOLUTE MAXIMUM RATINGS
V
All Other Pins..............................................-0.5V to (V
Short-Circuit Output Current (1sec) ....................................50mA
Continuous Power Dissipation (T
TIMING CHARACTERISTICS
(V
3-in-1 Silicon Delay Line
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
2
Note 1: Specifications to -40°C are guaranteed by design, not production tested.
Note 2: All voltages referenced to GND.
Note 3: Measured with outputs open.
Note 4: Guaranteed by design.
Note 5: Pulse width and/or period specifications may be exceeded, but accuracy is application sensitive (i.e., layout, decoupling, etc.).
Note 6: V
Note 7: The Part Number and Delay Times table provides typical delays at +25°C with V
Note 8: All output delays tend to vary unidirectionally with temperature or supply voltage variations (i.e., if OUT1 slows down, all
Supply Voltage
Input Voltage High
Input Voltage Low
Input Leakage Current
Active Current
Output Current High
Output Current Low
Input Capacitance
Input Pulse Width
Input-to-Output Delay
(leading edge)
Input-to-Output Delay
(trailing edge)
Power-Up Time
Period
8-Pin Plastic DIP (derate 9.1mW/°C above +70°C) .......727mW
14-Pin Plastic DIP (derate 10.0mW/°C above +70°C) ...800mW
CC
CC
CC
_______________________________________________________________________________________
to GND ..............................................................-0.5V to +6V
= +5.0V ±5%, T
= +5.0V ±5%, T
PARAMETER
PARAMETER
60ns, within ±3% for delays from 70ns to 100ns, and within ±5% for delays from 150ns to 200ns.
perature and supply variations. The combination of temperature (from +25°C to 0°C, or +25°C to +70°C) and supply varia-
tion (from 5V to 4.75V, or 5V to 5.25V) could produce an additional typical delay of ±1.5ns or ±3%, whichever is greater.
other outputs also slow down).
CC
= +5V at +25°C. Typical delays are accurate on both rising and falling edges within ±2ns for delays from 10ns to
A
A
= +25°C, unless otherwise noted.)
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +70°C)
SYMBOL
SYMBOL
V
t
t
I
C
V
I
I
t
V
t
PLH
PHL
CC
OH
OL
PU
I
WI
CC
IH
IL
L
IN
0V ≤ V
V
V
V
T
(Note 5)
(Notes 6, 7, 8)
(Notes 6, 7, 8)
(Note 5)
(Note 2)
(Note 2)
(Note 2)
A
CC
CC
CC
= +25°C (Note 4)
= 5.25V, period = minimum (Note 3)
= 4.75V, V
= 4.75V, V
CC
IN
CONDITIONS
+ 0.5V)
≤ V
CC
OH
OL
CONDITIONS
= 0.5V
= 4.0V
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
8-Pin SO (derate 5.9mW/°C above +70°C)....................471mW
16-Pin Narrow SO (derate 8.7mW/°C above +70°C) .....696mW
8-Pin µMAX (derate 4.1mW/°C above +70°C) ...............330mW
100% of t
3(t
MIN
WI
)
PLH
See Part Number and
See Part Number and
A
CC
= +25°C.)(Note 1)
Delay Times table
Delay Times table
= +5V. The delays may shift with tem-
TYP
4.75
MIN
2.2
12
-1
TYP
5.00
20
5
MAX
100
MAX
5.25
0.8
70
10
-1
1
UNITS
UNITS
mA
mA
mA
ms
µA
pF
ns
ns
ns
ns
V
V
V