m58bw16f Numonyx, m58bw16f Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
m58bw16f
Manufacturer Part Number
m58bw16f
Description
16 Or 32 Mbit X 32, Boot Block, Burst 3.3 V Supply Flash Memories
Manufacturer
Numonyx
Datasheet
1.M58BW16F.pdf
(87 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
m58bw16fB4T3F
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Company:
Part Number:
m58bw16fB4T3T
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Part Number:
m58bw16fB4ZA3
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
m58bw16fB4ZA3T
Manufacturer:
Micron Technology Inc
Quantity:
10 000
M58BW16F, M58BW32F
1
Description
The M58BW16F and M58BW32F are 16 and 32 Mbit non-volatile Flash memories,
respectively. They can be erased electrically at block level and programmed in-system on a
double-word basis using a 2.7 V to 3.6 V or 2.5 V to 3.3 V V
2.4 V to 3.6 V V
In the rest of the document the M58BW16F and M58BW32F will be referred to as
M58BWxxF unless otherwise specified.
The devices support Asynchronous (Latch Controlled and Page Read) and Synchronous
Bus operations. The Synchronous Burst Read interface allows a high data transfer rate
controlled by the Burst Clock signal, K. It is capable of bursting fixed or unlimited lengths of
data. The burst type, latency and length are configurable and can be easily adapted to a
large variety of system clock frequencies and microprocessors. All write operations are
asynchronous. On power-up the memory defaults to Read mode with an Asynchronous Bus.
The device features an asymmetrical block architecture:
●
●
Program and Erase commands are written to the command interface of the memory. An on-
chip Program/Erase controller simplifies the process of programming or erasing the memory
by taking care of all of the special operations that are required to update the memory
contents. The end of a Program or Erase operation can be detected and any error
conditions identified in the Status Register. The command set required to control the
memory is consistent with JEDEC standards.
Erase can be suspended in order to perform either Read or Program in any other block, and
then resumed. Program can be suspended to Read data in any other block, and then
resumed. Each block can be programmed and erased over 100,000 cycles.
The M58BW32F has an array of 62 main blocks of 512 Kbits each, plus 4 large
parameter blocks of 128 Kbits each and 8 small parameter blocks of 64 Kbits each. The
large and small parameter blocks are located either at the top (M58BW32FT) or at the
bottom (M58BW32FB) of the address space. The first large parameter block is referred
to as boot block and can be used either to store a boot code or parameters. The
memory array organization is detailed in
and
The M58BW16F has an array of 8 parameter blocks of 64 Kbits each and 31 main
blocks of 512 Kbits each. In the M58BW16FT the parameter blocks are located at the
top of the address space whereas in the M58BW16FB, they are located at the bottom.
The memory array organization is detailed in
addresses
Table 3: M58BW32F bottom boot block
DDQ
and
Table 5: M58BW16F bottom boot block
supply voltage for the input and output buffers.
Table 2: M58BW32F top boot block addresses
addresses.
Table 4: M58BW16F top boot block
DD
addresses.
supply for the circuit and a
Description
7/87