is42s16320b Integrated Silicon Solution, Inc., is42s16320b Datasheet - Page 47
![no-image](/images/no-image-200.jpg)
is42s16320b
Manufacturer Part Number
is42s16320b
Description
64m X 8, 32m X 16 512mb Synchronous Dram
Manufacturer
Integrated Silicon Solution, Inc.
Datasheet
1.IS42S16320B.pdf
(61 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
is42s16320b-6T
Manufacturer:
ISSI
Quantity:
1 000
Company:
Part Number:
is42s16320b-6TL
Manufacturer:
ISSI
Quantity:
1 060
Company:
Part Number:
is42s16320b-6TLI
Manufacturer:
NS
Quantity:
12
Company:
Part Number:
is42s16320b-6TLI
Manufacturer:
ISSI
Quantity:
2
Part Number:
is42s16320b-6TLI
Manufacturer:
ISSI
Quantity:
20 000
Company:
Part Number:
is42s16320b-75ETL
Manufacturer:
ISSI
Quantity:
1 000
Company:
Part Number:
is42s16320b-7BL
Manufacturer:
ISSI, Integrated Silicon Solution Inc
Quantity:
10 000
Part Number:
is42s16320b-7BLI
Manufacturer:
ISSI
Quantity:
20 000
Part Number:
is42s16320b-7TL
Manufacturer:
ISSI
Quantity:
20 000
IS42S86400B, IS42S16320B
PRECHARGE
The PRECHARGE command (see figure) is used to deac-
tivate the open row in a particular bank or the open row in
all banks.The bank(s) will be available for a subsequent row
access some specified time (t
command is issued. Input A10 determines whether one or
all banks are to be precharged, and in the case where only
one bank is to be precharged, inputs BA0, BA1 select the
bank. When all banks are to be precharged, inputs BA0,
BA1 are treated as “Don’t Care.” Once a bank has been
precharged, it is in the idle state and must be activated
prior to any READ or WRITE commands being issued to
that bank.
POWER-DOWN
Power-down occurs if CKE is registered LOW coincident
with a NOP or COMMAND INHIBIT when no accesses
are in progress. If power-down occurs when all banks are
idle, this mode is referred to as precharge power-down;
if power-down occurs when there is a row active in either
bank, this mode is referred to as active power-down.
Entering power-down deactivates the input and output
buffers, excluding CKE, for maximum power savings while
in standby. The device may not remain in the power-down
state longer than the refresh period (64ms) since no refresh
operations are performed in this mode.
The power-down state is exited by registering a NOP or
COMMAND INHIBIT and CKE HIGH at the desired clock
edge (meeting t
POWER-DOWN
Integrated Silicon Solution, Inc. — www.issi.com
Rev. 00F
08/11/08
cks
COMMAND
). See figure "Power-Down".
CKE
CLK
All banks idle
Enter power-down mode
rp
) after the PRECHARGE
t
NOP
CKS
Input buffers gated off
less than 64ms
PRECHARGE Command
Exit power-down mode
A0-A9, A11, A12
BA0, BA1
CKE
RAS
CAS
CLK
A10
WE
≥ t
CS
CKS
NOP
HIGH
DON'T CARE
ACTIVE
BANK ADDRESS
BANK SELECT
ALL BANKS
t
t
t
RCD
RAS
RC
47