lm2452 National Semiconductor Corporation, lm2452 Datasheet
lm2452
Related parts for lm2452
lm2452 Summary of contents
Page 1
... Monolithic Triple Channel 17 MHz DC Coupled CRT DTV Driver General Description The LM2452 is a triple channel high voltage DC coupled CRT driver circuit designed for use in DTV applications. The IC contains three high input impedance, wide band amplifi- ers which directly drive the RGB cathodes of a CRT. Each amplifier has a summing input where the DC level of the output is controlled by a low voltage DC input voltage ...
Page 2
... Note 7: Running the 1 MHz to 30 MHz test pattern at 1080i this part will dissipate approximately 15.2 W. This is the commonly accepted test pattern that is representative of the worst case high frequency content for normal television viewing. This is the pattern used to estimate the worst case power dissipation of the LM2452 in its normal application recommended to use a heat sink with a thermal resistance under 3˚C/W. www.national.com ...
Page 3
... Note load includes parasitic capacitance. Figure 3 shows a typical test circuit for evaluation of the LM2452. This circuit is designed to allow testing of the LM2452 in a 50Ω environment without the use of an expensive FET probe. The two 4990Ω resistors form a 400:1 divider with the 50Ω resistor and the oscilloscope ...
Page 4
... Typical Performance Characteristics (60V – 190V 50˚C, Test Circuit — Figure 3 unless otherwise specified) C FIGURE OUT FIGURE 5. LM2452 Pulse Response FIGURE 6. Bandwidth www.national.com (V = +220V , 20144504 FIGURE 7. Speed vs Load Capacitance IN 20144505 20144506 FIGURE 9. Speed vs Case Temperature 4 = +12V , pF, V ...
Page 5
... Typical Performance Characteristics (60V – 190V 50˚C, Test Circuit — Figure 3 unless otherwise specified) C FIGURE 10. Power Dissipation vs Frequency (V = +220V , 20144510 FIGURE 11. Safe Operating Area 20144512 FIGURE 12. LM2452 Cathode Response 5 = +12V , pF 130V OUT 20144511 www.national.com PP ...
Page 6
... The part is housed in a 15-lead TO-247 molded plastic power package with thin leads for improved metal-to-metal spacing. The circuit diagram of the LM2452 is shown in Figure 2 . The PNP emitter follower, Q5, provides input buffering. Q1 and Q2 form a fixed gain cascode amplifier with resistors R1 and R2 setting the gain at − ...
Page 7
... LM2452. One test MHz sine wave sweep over the active line. This would give a slightly lower power than taking the average of the power between 1 and 30 MHz. ...
Page 8
... CURRENT OUTPUT FOR IK FEEDBACK SYSTEMS The LM2452 can be used in DTV applications that use an IK feedback system. Figure 14 shows an example of an inter- face circuit used to feed back the IK output of LM2452 to a preamplifier with an ac coupled IK input. www.national.com This feedback system consists of the preamp, LM2452, and ...
Page 9
9 www.national.com ...
Page 10
... Application Hints (Continued) FIGURE 15. LM2452 DTV Demonstration Board Layout www.national.com 10 20144516 ...
Page 11
Application Hints (Continued) FIGURE 16. Trace Routing and Component Placement for Blue Channel Output 20144517 11 www.national.com ...
Page 12
... English www.national.com Français Tel: +33 ( 8790 NS Package Number TB15A Order Number LM2452TB 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system affect its safety or effectiveness. ...