lt5528euf-trpbf Linear Technology Corporation, lt5528euf-trpbf Datasheet
lt5528euf-trpbf
Related parts for lt5528euf-trpbf
lt5528euf-trpbf Summary of contents
Page 1
... The LO path consists buffer with single-ended input, and precision quadrature generators that produce the LO drive for the mixers. The supply voltage range is 4.5V to 5.25V. , LTC and LT are registered trademarks of Linear Technology Corporation LT5528 ...
Page 2
... EN = High 0dBm (Note 16 Low 0dBm (Note 16 High (Note Low (Note 6) (Note 5) at 2GHz (Note 5) at 2GHz (Note 5) at 2GHz U W TOP VIEW ORDER PART NUMBER LT5528EUF 12 GND GND 10 GND 9 UF PART MARKING UF PACKAGE 5528A = 125° ...
Page 3
ELECTRICAL CHARACTERISTICS BBPI, BBMI, BBPQ, BBMQ inputs 0.525V P = –10dBm, unless otherwise noted. (Note 3) RF, OUT SYMBOL PARAMETER Baseband Inputs (BBPI, BBMI, BBPQ, BBMQ) BW Baseband Bandwidth Common Mode Voltage CMBB R Single-Ended Input Resistance ...
Page 4
LT5528 W U TYPICAL PERFOR A CE CHARACTERISTICS = 0dBm. BBPI, BBMI, BBPQ, BBMQ inputs 0.525V sideband selection –10dBm (–10dBm/tone for 2-tone measurements), unless otherwise noted. (Note 3) RF, OUT Supply Current vs Supply Voltage 140 85°C 130 ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS = 0dBm. BBPI, BBMI, BBPQ, BBMQ inputs 0.525V sideband selection –10dBm (–10dBm/tone for 2-tone measurements), unless otherwise noted. (Note 3) RF, OUT 2 • LO Leakage to RF Output vs 2 ...
Page 6
LT5528 W U TYPICAL PERFOR A CE CHARACTERISTICS = 0dBm. BBPI, BBMI, BBPQ, BBMQ inputs 0.525V sideband selection –10dBm (–10dBm/tone for 2-tone measurements), unless otherwise noted. (Note 3) RF, OUT Gain vs LO Power –4 –6 –8 –10 ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS = 0dBm. BBPI, BBMI, BBPQ, BBMQ inputs 0.525V sideband selection –10dBm (–10dBm/tone for 2-tone measurements), unless otherwise noted. (Note 3) RF, OUT LO Feed-Through and Image Rejection at 2140MHz vs Baseband ...
Page 8
LT5528 W BLOCK DIAGRA U U APPLICATIO S I FOR ATIO The LT5528 consists of I and Q input differential voltage- to-current converters, I and Q up-conversion mixers output balun quadrature phase generator and LO buffers. ...
Page 9
U U APPLICATIO S I FOR ATIO and 12pF to ground is incorporated (see Figure 1), which limits the baseband bandwidth to approximately 330MHz (–1dB point). The common-mode voltage is about 0.52V and is approximately constant over temperature ...
Page 10
LT5528 U U APPLICATIO S I FOR ATIO LO Section The internal LO input amplifi er performs single-ended to differential conversion of the LO input signal. Figure 4 shows the equivalent circuit schematic of the LO input 20pF ...
Page 11
U U APPLICATIO S I FOR ATIO The RF output S with no LO power applied is given in 22 Table 4. Table 4. RF Port Output Impedance vs Frequency for EN = High and No LO Power Applied Frequency ...
Page 12
LT5528 U U APPLICATIO S I FOR ATIO Additionally, the exposed pad provides heat sinking for the part and minimizes the possibility of the chip overheating. If improved LO and Image suppression are required feed-through calibration and an ...
Page 13
U U APPLICATIO S I FOR ATIO Application Measurements The LT5528 is recommended for base-station applications using various modulation formats. Figure 12 shows a typi- cal application. The CAL box in Figure 12 allows for LO feed-through and Image suppression ...
Page 14
LT5528 U U APPLICATIO S I FOR ATIO internal circuit of the LT5528 is drawn. For best results, a high ohmic source is recommended; for example, the interface circuit drawn in Figure 3, modifi pulling resistors R5 and ...
Page 15
... SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights Package 16-Lead Plastic QFN (4mm × ...
Page 16
... Supply, 40MHz to 500MHz IF, –4dB to 57dB Linear Power Gain, 8.8MHz Baseband Bandwidth 17MHz Baseband Bandwidth, 40MHz to 500MHz IF, 1.8V to 5.25V Supply, –7dB to 56dB Linear Power Gain 500MHz BW S/H, 71.8dB SNR 500MHz BW S/H, 75.5dB SNR ● www.linear.com = 28mA, S 5528f LT/TP 1104 1K • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2004 ...