adg731bcp-reel7 Analog Devices, Inc., adg731bcp-reel7 Datasheet - Page 13

• Manufacturer Part Number: adg731bcp-reel7
• Description: 16-/32-channel, Serially Controlled 4
  1.8 V To 5.5 V, 2.5 V, Analog Multiplexersmultiplexers
• Manufacturer: Analog Devices, Inc.

REV. A
0.1 F
*SIMILAR CONNECTION FOR ADG725
Test Circuit 9. Channel-to-Channel Crosstalk
*SIMILAR CONNECTION FOR ADG725
0.1 F
CHANNEL-TO-CHANNEL CROSSTALK
*SIMILAR CONNECTION FOR ADG725
ADG731
V
V
ADG731*
DD
V
DD
V
DD
ADG731*
DD
V
GND
V
DD
GND
S
DD
V
V
Test Circuit 8. OFF Isolation
GND
SS
SS
INSERTION LOSS = 20 LOG
V
D
Test Circuit 10. Bandwidth
S
V
*
SS
SS
D
V
S32
0.1 F
V
S1
S2
SS
D
SS
0.1 F
50
50
OFF ISOLATION = 20 LOG
NETWORK
ANALYZER
50
= 20 LOG
R
V
OUT
L
50
R
50
ANALYZER
V
NETWORK
L
50
OUT
V
R
50
OUT
WITHOUT SWITCH
ANALYZER
NETWORK
V
50
L
V
OUT
WITH SWITCH
S
V
V
V
OUT
V
S
OUT
S
V
S
V
OUT
V
S
–13–
POWER-ON RESET
On power-up of the device, all switches will be in the OFF
condition. The Internal Shift Register is filled with zeros and
will remain so until a valid write takes place.
SERIAL INTERFACE
The ADG725 and ADG731 have a 3-wire serial interface
(SYNC, SCLK, and DIN) that is compatible with SPI, QSPI,
and MICROWIRE interface standards and most DSPs.
Figure 1 shows the timing diagram of a typical write sequence.
Data is written to the 8-bit Shift Register via DIN under the
control of the SYNC and SCLK signals.
When SYNC goes low, the Input Shift Register is enabled. An
8-bit counter is also enabled. Data from DIN is clocked into the
Shift Register on the falling edge of SCLK. Figures 2 and 3
show the contents of the Input Shift Registers for these devices.
When the part has received eight clock cycles after SYNC has
been pulled low, the switches are automatically updated with
the new configuration and the Input Shift Register is disabled.
The ADG725 CSA and CSB data bits allow the user the flex-
ibility to change the configuration of either or both banks of the
multiplexer.
MICROPROCESSOR INTERFACING
Microprocessor interfacing to the ADG725/ADG731 is via a serial
bus that uses standard protocol compatible with microcontrollers
and DSP processors. The communications channel is a 3-wire
interface consisting of a clock signal, a data signal, and a
synchronization signal. The ADG725/ADG731 requires an
8-bit data-word with data valid on the falling edge of SCLK.
Figures 4–7 illustrate simple 3-wire interfaces with popular
microcontrollers and DSPs.
ADSP-21xx to ADG725/ADG731 Interface
The ADSP-21xx family of DSPs are easily interfaced to the
ADG725/ADG731 without the need for extra logic. Figure 4
shows an example of an SPI interface between the ADG725/
ADG731 and the ADSP-2191M. SCK of the ADSP-2191M
drives the SCLK of the mux, while the MOSI output drives the
serial data line, DIN. SYNC is driven from one of the port lines,
in this case SPIxSEL.
Figure 4. ADSP-2191M to ADG725/ADG731 Interface
*ADDITIONAL PINS OMITTED FOR CLARITY
ADSP-2191M *
SPIxSEL
MOSI
SCK
ADG725/ADG731
ADG725/ADG731
SYNC
DIN
SCLK