hcpl0721 AGILTRON Incorporated, hcpl0721 Datasheet
hcpl0721
Available stocks
Related parts for hcpl0721
hcpl0721 Summary of contents
Page 1
Propagation Delay, CMOS Optocoupler Technical Data Features • CMOS Compatibility • max. Prop. Delay Skew • High Speed: 25 MBd • max. Prop. Delay • 10 kV/ s Minimum Common Mode Rejection ...
Page 2
Selection Guide 8-Pin DIP Small Outline (300 Mil) SO-8 HCPL-7721 HCPL-0721 HCPL-7720 HCPL-0720 Ordering Information Specify Part Number followed by Option Number (if desired) Example HCPL-7720#XXX No Option and Option 300 contain 50 units (HCPL-772X), 100 units (HCPL-072X) per tube. ...
Page 3
Package Outline Drawing HCPL-772X Package with Gull Wing Surface Mount Option 300 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). ...
Page 4
Solder Reflow Thermal Profile 260 240 220 T = 115°C, 0.3°C/SEC 200 180 160 140 120 100 100°C, 1.5°C/SEC TIME – MINUTES (NOTE: USE OF NON-CHLORINE ACTIVATED ...
Page 5
VDE 0884 Insulation Related Characteristics (Option 060) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage 150 V rms for rated mains voltage 300 V rms for rated mains voltage 450 V rms Climatic Classification Pollution ...
Page 6
Electrical Specifications Test conditions that are not specified can be anywhere within the recommended operating range. All typical specifications are + Parameter Symbol DC Specifications Logic Low Input I DD1L Supply Current Logic High ...
Page 7
Package Characteristics Parameter Input-Output Momentary 072X Withstand Voltage 772X Resistance (Input-Output) Capacitance (Input-Output) Input Capacitance Input IC Junction-to-Case -772X Thermal Resistance -072X Output IC Junction-to-Case -772X Thermal Resistance -072X Package Power Dissipation Notes: 1. Absolute Maximum ambient operating temperature means ...
Page 8
T (C) A Figure 4. Typical Pulse Width Distortion vs. Temperature PHL 21 T PLH ...
Page 9
Application Information Bypassing and PC Board Layout The HCPL-772X/072X optocouplers are extremely easy to use. No external interface circuitry is required because the HCPL-772X/072X use high-speed DD1 GND ...
Page 10
Pulse-width distortion (PWD) is the difference between t and PHL t and often determines the PLH maximum data rate capability of a transmission system. PWD can be expressed in percent by dividing the PWD (in ns) by the minimum pulse ...
Page 11
CONTROLLER BUS INTERFACE OPTICAL ISOLATION TRANSCEIVER FIELD BUS TRANSCEIVER TRANSCEIVER OPTICAL OPTICAL ISOLATION ISOLATION BUS BUS INTERFACE INTERFACE DEVICE CONFIGURATION MOTOR STARTER Figure 15. Typical Field Bus Communication Physical Model. Optical Isolation for Field Bus Networks To recognize the full ...
Page 12
Implementing CC-Link with the HCPL-772X/ 072X CC-Link (Control and Communication Link) is developed to merge control and information in the low-level network (field network) by PCs, thereby making the multivendor environment a reality. It has data control and message-exchange function, ...
Page 13
Implementing DeviceNet and SDS with the HCPL-772X/072X With transmission rates Mbit/s, both DeviceNet and SDS are based upon the same NODE/APP SPECIFIC uP/CAN HCPL HCPL 772x/072x 772x/072x TRANSCEIVER DRAIN/SHIELD SIGNAL POWER NETWORK POWER SUPPLY Figure 18. Isolated ...
Page 14
NODE/APP SPECIFIC uP/CAN HCPL 772x/072x 772x/072x TRANSCEIVER DRAIN/SHIELD SIGNAL POWER NETWORK * OPTIONAL FOR BUS V + SENSE POWER SUPPLY Figure 19. Isolated Node with Transceiver Powered by the Network. Isolated Node Providing Power to the Network Figure 20 shows ...
Page 15
Power Supplies and Bypassing The recommended DeviceNet application circuit is shown in Figure 21. Since the HCPL-772X/ 072X are fully compatible with CMOS logic level signals, the optocoupler is connected directly GALVANIC ISOLATION BOUNDARY ISO ...
Page 16
Power Supplies and Bypassing The recommended PROFIBUS application circuit is shown in Figure 23. Since the HCPL-772X/ 072X are fully compatible with CMOS logic level signals, the optocoupler is connected directly to the transceiver. Two bypass capacitors (with values between ...